Why Zanussi ZDLN1510 programme does not start?
If the programme on your Zanussi Dishwasher doesn't start, ensure the appliance door is fully closed. If the delay start is activated, either cancel the setting or wait for the countdown to finish. Also, the appliance may be recharging the resin inside the water softener, which takes about 5 minutes.
Why is the Zanussi ZDLN1510 door difficult to close?
If the door of your Zanussi Dishwasher is hard to close, the appliance might not be level. Try loosening or tightening the adjustable feet. Also, check if any tableware is protruding from the baskets.
What to do for malfunction of the water level detection sensor in Zanussi ZDLN1510?
If there's a malfunction with the water level detection sensor in your Zanussi Dishwasher, ensure that the filters are clean. You can also try switching the appliance off and on.
Why does the Zanussi ZDLN1510 programme last too long?
If a Zanussi Dishwasher program is running longer than expected, check if the delayed start option is enabled. If it is, cancel the delay setting or wait for the countdown to finish.
Why is my Zanussi Dishwasher not filling with water?
If your Zanussi Dishwasher isn't filling with water, check the following: 1. Ensure the water tap is fully open. 2. Verify that the water supply pressure is adequate. 3. Make sure the water tap isn't clogged. 4. Check that the filter in the inlet hose isn't clogged. 5. Confirm the inlet hose has no kinks or bends.
How to stop rattling sounds in my Zanussi ZDLN1510 Dishwasher?
If you hear rattling or knocking sounds from inside your Zanussi Dishwasher, ensure the tableware is properly arranged in the baskets, referring to the basket loading leaflet. Also, check that the spray arms can rotate freely.
Why is the water level too high in my Zanussi ZDLN1510 Dishwasher?
If the water level inside your Zanussi Dishwasher is too high, first switch the appliance off and on. Also, make sure that the filters are clean and that the outlet hose is installed at the correct height above the floor, according to the installation instructions.
What to do if the anti-flood device is on in my Zanussi Dishwasher?
If the anti-flood device on your Zanussi Dishwasher is activated, close the water tap. Ensure the appliance is correctly installed and that the baskets are loaded as instructed in the user manual.
Why does my Zanussi ZDLN1510 trip the circuit breaker?
If your Zanussi Dishwasher is tripping the circuit-breaker, it could be due to insufficient amperage. Check the socket amperage and the capacity of the meter, or turn off another appliance in use. If this doesn't resolve the issue, there may be an internal electrical fault.
What to do if the Zanussi Dishwasher programme does not start?
If your Zanussi Dishwasher program isn't starting, make sure the appliance door is fully closed. Also, check if the delay start function is activated; if so, either cancel the setting or wait for the countdown to finish. The appliance may also be recharging the resin inside the water softener, which takes about 5 minutes.
General| Type | Freestanding |
|---|---|
| Appliance placement | Freestanding |
| Control panel colour | White |
| Noise Level | 49 dB |
| Number of Washing Programs | 5 |
| Delayed Start Timer | Yes |
| Delay Start (max) | 24 hours |
| Energy Efficiency Class | F |
| Energy Consumption per Cycle | 1.039 kWh |
| Annual Energy Consumption | 295 kWh |
| Drying Class | A |
| Half Load Option | No |
| Child Lock | No |
| Drying system | Residual heat |
| Product size | 60 cm |
| Number of Place Settings | 13 |
| Wash Programs | Eco, Intensive, Normal, Quick |
| Water Consumption per Cycle | 11 litres |
| Annual Water Consumption | 3080 L |
| Programs | Eco, Intensive, Normal, Quick |
To Next Page
