What to do if my Zanussi Dishwasher shows error i61 or i69?
If the temperature of the water inside your Zanussi Dishwasher is too high, or if a malfunction of the temperature sensor occurred and the display shows i61 or i69, make sure that the temperature of the inlet water does not exceed 60°C. You can also try switching the appliance off and on.
What to do if my Zanussi ZDLN6531 is not draining water and the display shows i20?
If your Zanussi dishwasher is not draining water and the display shows i20, check that the sink spigot and the interior filter system are not clogged. Also, make sure that the drain hose has no kinks or bends.
How to activate Zanussi ZDLN6531 Dishwasher?
If your Zanussi Dishwasher won't activate, ensure that the mains plug is properly connected to the mains socket. Also, check your fuse box to make sure there are no damaged fuses.
How to fix technical malfunction of the Zanussi ZDLN6531? The display shows iC0 or iC3.
If your Zanussi Dishwasher displays iC0 or iC3, indicating a technical malfunction, switch the appliance off and on.
What does i61 mean on my Zanussi ZDLN6531?
If your Zanussi Dishwasher displays i61 or i69, it indicates that the water temperature is too high or there's a temperature sensor malfunction. Ensure that the inlet water temperature does not exceed 60°C. You can also try switching the appliance off and on.
What to do if the anti-flood device is on in my Zanussi ZDLN6531 Dishwasher and the display shows i30?
If the anti-flood device is activated in your Zanussi Dishwasher and the display shows i30, close the water tap. Ensure that the appliance is correctly installed and that the baskets are loaded as instructed in the user manual.
How to fix small leak from Zanussi Dishwasher door?
If there is a small leak from the door of your Zanussi Dishwasher, the appliance may not be levelled. Loosen or tighten the adjustable feet to correct this. Also, the door may not be centred on the tub; adjust the rear foot if applicable.
Why does my Zanussi ZDLN6531 Dishwasher stop and start during operation?
It is normal for your Zanussi Dishwasher to stop and start during operation. This provides optimal cleaning results and energy savings.
What does iF1 mean on my Zanussi ZDLN6531 Dishwasher?
If the water level inside your Zanussi Dishwasher is too high and the display shows iF1, try switching the appliance off and on. Also, make sure that the filters are clean and that the outlet hose is installed at the right height above the floor, as specified in the installation instructions.
Why does my Zanussi Dishwasher programme last too long?
If your Zanussi Dishwasher programme lasts too long, check if the delay start option is set and cancel the delay setting or wait for the end of the countdown. Also, activating options can increase the programme duration.
General| Product size | Full size (60 cm) |
|---|---|
| Control panel colour | Black |
| Number of Place Settings | 13 |
| Noise Level | 44 dB |
| Number of washing programs | 8 |
| Washing class | A |
| Drying class | A |
| Cycle time | 240 min |
| Annual Energy Consumption | 237 kWh |
| Drying Performance | A |
| Cleaning Performance | A |
| Delay Start | Yes |
| Half Load Option | Yes |
| Width | 596 mm |
| Depth | 550 mm |
| Height | 818 mm |
| Appliance placement | Built-in |
| Water consumption per cycle | 9.9 L |
| Annual Water Consumption | 2772 L |
| Programs | Eco, Glass, Intensive, Quick |
| Drying system | AirDry |
To Next Page
