What causes stains and dry water drops on glasses and dishes in my Zanussi ZDLN6531?
If there are stains and dry water drops on glasses and dishes from your Zanussi Dishwasher, the released quantity of rinse aid may not be sufficient. Adjust the rinse aid dosage to a higher level, or the quality of the rinse aid can be the cause.
What to do if my Zanussi Dishwasher shows error i61 or i69?
If the temperature of the water inside your Zanussi Dishwasher is too high, or if a malfunction of the temperature sensor occurred and the display shows i61 or i69, make sure that the temperature of the inlet water does not exceed 60°C. You can also try switching the appliance off and on.
Why does my Zanussi Dishwasher programme last too long?
If your Zanussi Dishwasher programme lasts too long, check if the delay start option is set and cancel the delay setting or wait for the end of the countdown. Also, activating options can increase the programme duration.
Why is my Zanussi Dishwasher door difficult to close?
If your Zanussi Dishwasher door is difficult to close, it might not be levelled. Try loosening or tightening the adjustable feet. Also, check if any tableware parts are protruding from the baskets.
What to do if my Zanussi ZDLN6531 Dishwasher shows iF1?
If the level of water inside your Zanussi Dishwasher is too high and the display shows iF1, try switching the appliance off and on. Also, make sure that the filters are clean and that the outlet hose is installed at the right height above the floor, referring to the installation instructions.
What to do if the anti-flood device is on in my Zanussi ZDLN6531 Dishwasher and the display shows i30?
If the anti-flood device is activated in your Zanussi Dishwasher and the display shows i30, close the water tap. Ensure that the appliance is correctly installed and that the baskets are loaded as instructed in the user manual.
What does it mean if the interior of my Zanussi ZDLN6531 Dishwasher is wet?
If the interior of your Zanussi Dishwasher is wet, this is not a defect of the appliance. Humidity condensates on the appliance walls.
What to do if my Zanussi ZDLN6531 doesn't drain water and shows i20?
If your Zanussi Dishwasher isn't draining water and the display shows i20, make sure that the sink spigot is not clogged. Also, check that the interior filter system is not clogged and that the drain hose has no kinks or bends.
Why is there a small leak from the Zanussi Dishwasher door?
If you notice a small leak from your Zanussi Dishwasher door, the appliance might not be levelled. Try loosening or tightening the adjustable feet. If applicable, adjust the rear foot if the door is not centered on the tub.
How to activate Zanussi ZDLN6531 Dishwasher?
If your Zanussi Dishwasher won't activate, ensure that the mains plug is properly connected to the mains socket. Also, check your fuse box to make sure there are no damaged fuses.
General| Product size | Full size (60 cm) |
|---|---|
| Control panel colour | Black |
| Number of Place Settings | 13 |
| Noise Level | 44 dB |
| Number of washing programs | 8 |
| Washing class | A |
| Drying class | A |
| Cycle time | 240 min |
| Annual Energy Consumption | 237 kWh |
| Drying Performance | A |
| Cleaning Performance | A |
| Delay Start | Yes |
| Half Load Option | Yes |
| Width | 596 mm |
| Depth | 550 mm |
| Height | 818 mm |
| Appliance placement | Built-in |
| Water consumption per cycle | 9.9 L |
| Annual Water Consumption | 2772 L |
| Programs | Eco, Glass, Intensive, Quick |
| Drying system | AirDry |
To Next Page
