Zaxcom NOVA - False Start Handling; Marking or Deleting False Starts

54 pages

Save Page as PDF

To Next Page

To Previous Page

NOVA OPERATIONS False Start

False Start

Pressing STOP key after stopping will open the false start page. From this page a

take can be marked as a false start or just delete the file.

Main Page

Default Chapter2
- Table of Contents2
Nova6
- Front Panel6
- Left Side9
- Right Side10
- Rear11
Main Menu12
- Sub Menus12
Assigning Inputs to a Fader / Bank13
- Setting a Cross Point13
- Changing Banks13
Naming Tracks14
- How to Name a Track14
- Selecting from the List of Preset Track Names14
Memory Menu15
- Store / Recall Memory15
  - How to Store and Recall a Setup Parameter15
- Clear Fader Assigns15
- Factory Reset to Default15
- Store / Recall to Mirror Card15
Headphone Setup16
- Setting up Headphone Presets16
- Naming the Headphone Setup16
- Inverting the Phase of a Selection16
  - Headphone Matrix Setup to Decode Ms Stereo16
Eng Menu17
- Compressors17
  - Compressor Enable17
  - Compressor Parameters Set17
- Levels17
  - Internal & External Slate Levels17
  - Extra Input Gain17
  - TA5 Output Levels Adjust17
- Sample Rate Select18
- Prerecord18
- Tc Transport18
- Lcd Brightness18
- Led Brightness18
- Slate Microphone Source18
- Multi-Trim18
- Play to Outputs18
- Gp Remote Roll Enable19
- Punch-In19
- Tone Frequency Adjust19
- Tone Level19
- Meter Peak Hold Set19
- Transport Keys19
- Inverted Xpoints19
- Track Name Preset Edit19
- Note Presets Edit20
- Headphone 1 Volume20
- About Nova Menu20
  - Warnings Setup20
- Setup Power20
- Advanced Setup21
  - Prevent Empty Pan21
  - Display Speed21
  - Update Bootloader21
  - Update IFB Module21
  - Debug Bits21
  - Allow Logging21
  - Log Screen21
  - Upgrade Code21
  - Slate Always on21
  - Slate Delay22
  - Button Hold Time22
Setting the Input Parameters23
- Navagating the Input Setup Menu23
- Adjustable Parameters23
- Input Compressor Linking23
Time Code24
- Jamming Time Code and User Bits24
- Manually Entering Time Code and User Bits24
  - Entering Time Code24
  - Entering User-Bits24
- Time Code Setup Menu25
Assigning Inputs to the Record Tracks27
- Navagating the Track Assign Matrix27
- Setting a Record Cross Point27
Zaxnet Setup Menu28
- Zaxnet Enable28
- Tx Channel28
- Ifb Audio Source28
- Group Code28
- Tx Power28
- Transport Commands28
- Power-Roll Mode28
- TRX Off-On29
- Send Erx Delay29
- Zaxnet TC out29
- Ifb Test Tone29
- Update Ifb Module29
- Ifb Debug29
Metadata Menu30
- Entering / Editing Metadata30
- Note Preset30
  - How to Select and Enter a Note from the Preset List of Notes30
Cue / Playback Control Menu31
- Playing Back a File31
- Wireless Audition and Re-Record31
  - How to Audition and Re-Record a File31
Record Enables Matrix32
- Enabling Record Tracks32
Output Assign Routing33
- Navagating the Output Bus Matrix33
  - Output Busses 1 Thru 433
  - Output Busses 5 and 633
- Setting a Cross Point33
Media Menu34
- Mirror Mode Options34
- Write Sound Report34
- Primary Card Menu35
- Mirror Settings Menu37
Wireless Receiver Setup39
- Receiver View39
- Scan Menu40
- Center Frequency Set40
- Qrx Program40
Adjusting Input Trim and Remote Transmitter Gain41
- Adjusting the Input Trim41
- Adjusting the Transmitter Gain41
Setting up and Engaging Tone42
- Assigning Tone to Output Busses42
- Assigning Tone to Card Tracks42
- Adjusting the Tone Frequency and Level42
- Turning On/Off Tone42
Using the Onscreen Keyboard43
Monitoring44
- Changing Headphone Presets44
- Pre Fader Listining44
False Start45
Compact Flash Cards46
Syncing Nova to a Denecke Slate47
Nova Connector Assignments48
- Audio Input / Output Connectors (Xlr-3)48
- Audio Output Connectors (Ta-5)48
- Slate Microphone Input Connector (1/8" Trs)48
- Headphone Output Connectors (1/4" Trs)48
- Power Connectors (Hirose-4 Connector)48
- Aes Digital Input / Output Connectors (Db-15)49
Updating Firmware50
- Updating Nova S Firmware50
- Updating the Receiver Modules Firmware Using a Zaxcom Transmitter50
Product Support51
Nova Specifications52
Zaxcom Warranty Policy and Limitations54

Zaxcom NOVA - False Start Handling; Marking or Deleting False Starts

Table of Contents