How to switch on Zeiss Axio Zoom.V16 Microscope if it cannot be switched on at the HIP?
If your Zeiss Microscope cannot be switched on at the HIP, the issue might be due to an interrupted mains supply or the STOP button being pressed. First, check and restore the mains supply. Then, unlock the STOP button by pulling it out.
Provides general information about the Axio Zoom.V16 microscope and safety symbols.
Details safety precautions and guidelines for using the Axio Zoom.V16 microscope.
Outlines the manufacturer's warranty terms and conditions for the instrument.
Details the various components and configurations of the Axio Zoom.V16 microscope systems.
Illustrates and describes the various mechanical connection points and dimensions.
Lists the physical dimensions, weight, and optical risk classification of the microscope.
Provides an overview of the setup process, including services and safety prerequisites.
Details the procedure for installing the various stand components and their correct placement.
Explains how to securely mount the microscope body onto the carrier or nosepiece.
Guides the user on how to properly insert eyepieces and attach fold-over eyecups.
Details the steps for connecting the Human Interface Panel (HIP) to the microscope.
Explains how to mount and connect the Manual Rotary Control (MaRC) unit to the microscope.
Details the process of mounting different types of stages and their associated adapters.
Explains how to mount different reflected light illumination units onto the objective.
Details mounting reflected light illuminators using M8 tapped holes with carriers and holders.
Guides the installation of the transmitted light unit S, including base insert plate and glass plates.
Instructions for changing the insert plate 450, including safety precautions for hot surfaces.
Details the process of inserting the VisiLED transmitted light unit H into the stand base 450.
Explains how to install camera adapters for different interfaces (60N, 60) and basic microscope settings.
Details how to make the necessary electrical connections for the microscope system, including CAN bus.
Describes the functionality and setup of the Human Interface Panel (HIP) for microscope control.
Explains the functions and operation of the Manual Rotary Control (MaRC) unit for zoom and focus.
Details saving and recalling a focus position using the MaRC unit.
Explains how to reverse the rotation direction of the MaRC control unit.
Provides instructions for switching the microscope system on correctly.
Details the procedure for safely switching off the microscope system.
Describes the function and operation of the STOP button for deactivating the focusing drive.
Guides on how to adjust the lower limit switch for the motorized focusing drive to prevent collisions.
Covers various settings and adjustments for microscope operation.
Details the fundamental steps for setting up and adjusting the microscope for optimal viewing.
Explains how to set up and use the fiber-optic slit-ring illuminator and its accessories.
Details the setup and operation of VisiLED ring illuminators, including different modes.
Covers the use of fiber-optic and LED ring illuminators for reflected light darkfield applications.
Explains the assembly and alignment of flexible light guides with focusing attachments on light brackets or articulated arms.
Details the use of swan neck light guides for spatial object observation with selective shadow effect.
Describes the assembly and operation of the retractable fiber optic diffuser for low-reflex illumination.
Explains the use of fiber-optic surface light for low-reflex illumination of shiny objects.
Details the working position and adjustment of the Line Light S for oblique high-contrast illumination.
Provides general remarks on adjusting illumination controllers and safety for LED and cold light sources.
Guides on setting up the transmitted light illuminator S, including opal glass plate and anti-glare shield.
Details how to adjust the transillumination base 300 for different illumination methods and effects.
Outlines the basic care requirements for the equipment, including cleaning optical and plastic surfaces.
Covers safety checks for the focusing drive and procedures for relocating the microscope.
Lists wearing parts available for order from Carl Zeiss, along with catalogue numbers.
Recommends service/maintenance agreements and how to contact Carl Zeiss representatives.
Provides information on the proper disposal of the product according to EU directives and local laws.
Defines common abbreviations used throughout the operating manual for clarity.
Lists common errors and their corresponding remedies for the microscope system.
An index of all figures included in the manual, with their corresponding page numbers.
An alphabetical index of terms and topics covered in the manual, with page references.
Provides general information about the Axio Zoom.V16 microscope and safety symbols.
Details safety precautions and guidelines for using the Axio Zoom.V16 microscope.
Outlines the manufacturer's warranty terms and conditions for the instrument.
Details the various components and configurations of the Axio Zoom.V16 microscope systems.
Illustrates and describes the various mechanical connection points and dimensions.
Lists the physical dimensions, weight, and optical risk classification of the microscope.
Provides an overview of the setup process, including services and safety prerequisites.
Details the procedure for installing the various stand components and their correct placement.
Explains how to securely mount the microscope body onto the carrier or nosepiece.
Guides the user on how to properly insert eyepieces and attach fold-over eyecups.
Details the steps for connecting the Human Interface Panel (HIP) to the microscope.
Explains how to mount and connect the Manual Rotary Control (MaRC) unit to the microscope.
Details the process of mounting different types of stages and their associated adapters.
Explains how to mount different reflected light illumination units onto the objective.
Details mounting reflected light illuminators using M8 tapped holes with carriers and holders.
Guides the installation of the transmitted light unit S, including base insert plate and glass plates.
Instructions for changing the insert plate 450, including safety precautions for hot surfaces.
Details the process of inserting the VisiLED transmitted light unit H into the stand base 450.
Explains how to install camera adapters for different interfaces (60N, 60) and basic microscope settings.
Details how to make the necessary electrical connections for the microscope system, including CAN bus.
Describes the functionality and setup of the Human Interface Panel (HIP) for microscope control.
Explains the functions and operation of the Manual Rotary Control (MaRC) unit for zoom and focus.
Details saving and recalling a focus position using the MaRC unit.
Explains how to reverse the rotation direction of the MaRC control unit.
Provides instructions for switching the microscope system on correctly.
Details the procedure for safely switching off the microscope system.
Describes the function and operation of the STOP button for deactivating the focusing drive.
Guides on how to adjust the lower limit switch for the motorized focusing drive to prevent collisions.
Covers various settings and adjustments for microscope operation.
Details the fundamental steps for setting up and adjusting the microscope for optimal viewing.
Explains how to set up and use the fiber-optic slit-ring illuminator and its accessories.
Details the setup and operation of VisiLED ring illuminators, including different modes.
Covers the use of fiber-optic and LED ring illuminators for reflected light darkfield applications.
Explains the assembly and alignment of flexible light guides with focusing attachments on light brackets or articulated arms.
Details the use of swan neck light guides for spatial object observation with selective shadow effect.
Describes the assembly and operation of the retractable fiber optic diffuser for low-reflex illumination.
Explains the use of fiber-optic surface light for low-reflex illumination of shiny objects.
Details the working position and adjustment of the Line Light S for oblique high-contrast illumination.
Provides general remarks on adjusting illumination controllers and safety for LED and cold light sources.
Guides on setting up the transmitted light illuminator S, including opal glass plate and anti-glare shield.
Details how to adjust the transillumination base 300 for different illumination methods and effects.
Outlines the basic care requirements for the equipment, including cleaning optical and plastic surfaces.
Covers safety checks for the focusing drive and procedures for relocating the microscope.
Lists wearing parts available for order from Carl Zeiss, along with catalogue numbers.
Recommends service/maintenance agreements and how to contact Carl Zeiss representatives.
Provides information on the proper disposal of the product according to EU directives and local laws.
Defines common abbreviations used throughout the operating manual for clarity.
Lists common errors and their corresponding remedies for the microscope system.
An index of all figures included in the manual, with their corresponding page numbers.
An alphabetical index of terms and topics covered in the manual, with page references.
General| Brand | Zeiss |
|---|---|
| Model | Axio Zoom.V16 |
| Category | Microscope |
| Language | English |
To Next Page
