3M HCD-1 - HOW TO CUSTOMIZE WATER TEMPERATURE; Customize Hot Water Temperatures; Customize Cold Water Temperatures

•
While
the touch screen panel is locked, you can dispense hot/cold water
2.
To unlock the panel,
•
A beep sounds once and
the panel is now unlocked.
U
V
1.
Tap the UV button
•
A beep sounds once and the UV indicator lights up, indicating that the UV lamp
is now switched on.
•
The UV lamp
HOW TO CUSTOMIZE WATER TEMPERATURE
How to Customize Hot Water T
emperatures
The default temperature for hot water is set at approximately 86
The temperature for hot water can be customized between 83
1.
Tap the Power button to switch off the dispenser.
2. Tap and hold the Hot
button for 3 seconds.
•
A beep sounds once and the Hot Water Temperature indicator
3.
Tap the Hot button again to raise the Hot Water Temperature indicator by 1 level each time.
•
The highest temperature for hot water is at 90
• Whe
n the indicator is at level 4, tapping the Hot button will bring the Hot Water Temperature to
level 0.
4. After the temperature is set,
settings to be saved automatically.
5. Tap the Powe
r button to switch on the dispenser and continue with use.
How to Customize Cold Water Temperatures
The default temperature for cold
water is set at approximately 5.8
The temperature for cold water can be customized between 5.0
1.
Tap the Power button to switch off the dispenser.
2.
Tap and hold the Cold button for 3 seconds.
•
A beep sounds once and the Cold Water Temperature indicator
3.
Tap the Cold button again to raise the Cold Water Temperature indicator
•
The lowest temperature for cold water is at 5.0
10
the touch screen panel is locked, you can dispense hot/cold water
To unlock the panel,
tap
and hold the Auto Dispense button for three seconds.
A beep sounds once and
the Auto Dispense indicator
turns off, indicating that
the panel is now unlocked.
Tap the UV button
.
A beep sounds once and the UV indicator lights up, indicating that the UV lamp
is now switched on.
The UV lamp
sterilizes the filtered water before sending it to the storage tank.
HOW TO CUSTOMIZE WATER TEMPERATURE
emperatures
The default temperature for hot water is set at approximately 86
o
C.
The temperature for hot water can be customized between 83
o
C (minimum) to 90
o
C (maximum).
Tap the Power button to switch off the dispenser.
button for 3 seconds.
A beep sounds once and the Hot Water Temperature indicator
(RED)
blinks at level 2.
Tap the Hot button again to raise the Hot Water Temperature indicator by 1 level each time.
The highest temperature for hot water is at 90
o
C (level 4).
n the indicator is at level 4, tapping the Hot button will bring the Hot Water Temperature to
tap the Power button to save the settings, or wait for 10 seconds for the
settings to be saved automatically.
r button to switch on the dispenser and continue with use.
How to Customize Cold Water Temperatures
water is set at approximately 5.8
o
C.
The temperature for cold water can be customized between 5.0
o
C (minimum) to 7.0
o
C (m
aximum).
Tap the Power button to switch off the dispenser.
Tap and hold the Cold button for 3 seconds.
A beep sounds once and the Cold Water Temperature indicator
(BLUE)
blinks at level 2.
Tap the Cold button again to raise the Cold Water Temperature indicator
by 1 level each time.
The lowest temperature for cold water is at 5.0
o
C (level 4).
the touch screen panel is locked, you can dispense hot/cold water
.
and hold the Auto Dispense button for three seconds.
turns off, indicating that
A beep sounds once and the UV indicator lights up, indicating that the UV lamp
sterilizes the filtered water before sending it to the storage tank.
C (maximum).
blinks at level 2.
Tap the Hot button again to raise the Hot Water Temperature indicator by 1 level each time.
n the indicator is at level 4, tapping the Hot button will bring the Hot Water Temperature to
tap the Power button to save the settings, or wait for 10 seconds for the
aximum).
blinks at level 2.
by 1 level each time.