3M HCD-1 - How to Use Panel Functions

HOW TO USE
PANEL FUNCTIONS
Cold Water
1.
Ensure that the dispenser is switched on.
2.
Tap the Cold button.
•
A beep sounds once and the Cold i
3.
Press the cold water lever to dispense water.
• Do not
dispense if the Water Level indicator is not lit.
Hot Water
1.
Ensure that the dispenser is switched on.
2.
Tap the Hot button.
•
A beep sounds once and the Hot indicator lights up.
3.
Tap the Safety Lock button once, then press the lever.
•
When the Safety Lock button is tapped, a beep sounds once and the red Safety
Lock indicator lights up.
•
Press the lever within 3 seconds to discharge hot water.
•
As the hot water is discharged, water fr
hot water tank. Hence, the hot water temperature level goes down.
•
If the lever is not pressed within 3 seconds after tapping the Safety Lock button,
the red indicator turns off and the hot water dispenser becomes l
Econ Mode
1.
Tap this button to enable the power saving mode.
2.
Once the button is tapped, a beep sounds once and the Econ Mode indicator lights
up.
•
When the Econ Mode is switched on, the operating frequency of the compressor
and heater inside
save power. Hence, when the dispenser is in Econ Mode, cold water becomes
less cold and hot water becomes less hot.
•
If water is not cold or hot enough (when the surroundings are dark), check if t
Econ Mode indicator is lit. If yes, switch off the Econ Mode by tapping once.
Auto Dispense
1.
Tap the Auto Dispense Button.
•
A beep sounds once and the Cold Water
Temperature indicator moves up and
down from
dispenser is ready
•
Press the cold water lever once to discharge up to 1 liter of cold water. This
takes about 28 seconds.
•
For safety reasons, only cold water can be dispensed continuously.
2.
To stop continuous dispen
Lock the Touch Screen Panel
1. Tap
and hold the Auto Dispense button for 3 seconds to lock the panel.
•
A beep sounds twice and
the panel is
9
PANEL FUNCTIONS
Ensure that the dispenser is switched on.
Tap the Cold button.
A beep sounds once and the Cold i
ndicator lights up.
Press the cold water lever to dispense water.
dispense if the Water Level indicator is not lit.
Ensure that the dispenser is switched on.
Tap the Hot button.
A beep sounds once and the Hot indicator lights up.
Tap the Safety Lock button once, then press the lever.
When the Safety Lock button is tapped, a beep sounds once and the red Safety
Lock indicator lights up.
Press the lever within 3 seconds to discharge hot water.
As the hot water is discharged, water fr
om the cold water tank will flow into the
hot water tank. Hence, the hot water temperature level goes down.
If the lever is not pressed within 3 seconds after tapping the Safety Lock button,
the red indicator turns off and the hot water dispenser becomes l
ocked again.
Tap this button to enable the power saving mode.
Once the button is tapped, a beep sounds once and the Econ Mode indicator lights
When the Econ Mode is switched on, the operating frequency of the compressor
and heater inside
the dispenser is reduced (when the surroundings are dark) to
save power. Hence, when the dispenser is in Econ Mode, cold water becomes
less cold and hot water becomes less hot.
If water is not cold or hot enough (when the surroundings are dark), check if t
Econ Mode indicator is lit. If yes, switch off the Econ Mode by tapping once.
Tap the Auto Dispense Button.
A beep sounds once and the Cold Water
Temperature indicator moves up and
down from
level 1 to 4, indicating that the
dispenser is ready
for Auto Dispense.
Press the cold water lever once to discharge up to 1 liter of cold water. This
takes about 28 seconds.
For safety reasons, only cold water can be dispensed continuously.
To stop continuous dispen
sing, press the cold water lever again.
Lock the Touch Screen Panel
and hold the Auto Dispense button for 3 seconds to lock the panel.
A beep sounds twice and
the Auto Dispense indicator lights up, indicating that
the panel is
now locked.
When the Safety Lock button is tapped, a beep sounds once and the red Safety
om the cold water tank will flow into the
If the lever is not pressed within 3 seconds after tapping the Safety Lock button,
ocked again.
Once the button is tapped, a beep sounds once and the Econ Mode indicator lights
When the Econ Mode is switched on, the operating frequency of the compressor
the dispenser is reduced (when the surroundings are dark) to
save power. Hence, when the dispenser is in Econ Mode, cold water becomes
If water is not cold or hot enough (when the surroundings are dark), check if t
he
Econ Mode indicator is lit. If yes, switch off the Econ Mode by tapping once.
Press the cold water lever once to discharge up to 1 liter of cold water. This
the Auto Dispense indicator lights up, indicating that