10
5.5 RFID TAG:
The Lad-Saf
™
system and the Lad-Saf
™
X2 Detachable Cable Sleeve include a Radio Frequency Identication (RFID) tag
(Figure 2, Item O & Figure 11, Item 4). The RFID tag can be used in conjunction with a handheld reading device and
web based portal to simplify inspection and inventory control and provide records for your fall protection equipment. If
you are a rst-time user, contact a Capital Safety Customer Service representative (see back cover),
If you have already
registered, go to www.capitalsafety.com/isafe.html.
Follow the instructions provided with your handheld reader or on the
web portal to transfer your data to your web log.
6.0 MAINTENANCE, SERVICING, STORAGE
6.1 See section 5.0 for inspection related maintenance issues. If the carrier cable becomes heavily soiled with oil, grease, paint, or other
substances, clean it with warm soapy water. Wipe off the cable with a clean, dry cloth. Do not force dry with heat. Do not use
acid or caustic chemicals that could damage the cable.
Additional maintenance and servicing procedures must be completed by an authorized service center. Authorization must
be in writing.
The Lad-Saf
™
X2 Detachable Cable Sleeve may be cleaned with warm, soapy water.
Store the Lad-Saf
™
X2 Detachable Cable Sleeve in a cool, dry, clean environment, out of direct sunlight. Avoid areas
where chemicals vapors exist. Thoroughly inspect the sleeve after extended storage.
Transport the Lad-Saf
™
system in an enclosure to protect it from any cuts, moisture or ultraviolet light. Avoid corrosive,
overheated or refrigerated atmospheres.
IMPORTANT: Do not disassemble sleeve. If the Lad-Saf
™
X2 Detachable Cable Sleeve is
disassembled or tampered with in any manner it may result in serious injury or death.
7.0 SPECIFICATIONS
7.1 All top and bottom brackets, cable guides, carrier cable, and fasteners are made of galvanized or stainless steel. Contact
DBI-SALA for material specication details if required. The Lad-Saf
™
system, when installed according to the user
instructions, meets OSHA, ANSI (A14.3), CSA (Z259.2.5) and CE (EN353-1:2014) requirements.
8.0 LABELING, ID/LOT NUMBERS, MANUFACTURING DATES
The Lad-Saf
™
Flexible Cable Ladder Safety System label (see Figure 11) must be securely attached and fully legible:
1. Acceptable cable sleeve part numbers associated with exible cable size.
2. WARNING: Failure to heed warnings may result in serious injury or death. Manufacturer’s instructions supplied with this
product at time of shipment must be followed for proper installation, use, inspection and maintenance. Unauthorized
alteration or substitution of system elements or components is prohibited. Do not use system with incompatible safety
sleeves. Before each use inspect system visually for defects. Formally inspect system in accordance with instructions at
least annually. Refer to instructions for information on periodic formal inspections. Minimum spacing of users of this system
is 20 ft.
3. Serial Number
4. RFID Tag
5. System Installation Date
6. Proof Test Completed
7. Inspected By
8. Date of Inspection
9. Inspections
10. System Capacity
The following Lad-Saf
™
X2 Detachable Cable Sleeve labels must be securely attached and fully legible:
Label in Figure 12, Model 6160030:
1. Model Number
2. Serial Number
3. WARNING: Failure to heed warnings may result in serious injury or death. Read and follow manufacturer’s instructions
supplied with this product before use. Use only with DBI-SALA approved system and harness. Inspect before each use.
Attach sleeve to frontal D-ring on harness with DBI-SALA supplied carabiner.
Label in Figure 13, Model 6160047
1. Model Number
2. Serial Number
3. WARNING: Failure to heed warnings may result in serious injury or death. Read and follow manufacturer’s instructions
supplied with this product before use. Use only with DBI-SALA approved system and harness. Inspect before each use.
Attach sleeve to frontal D-ring on harness with DBI-SALA supplied carabiner.
Label in Figure 14, Model 6160030 and 6160047:
1. UP orientation of sleeve body.
Handle/Energy Absorber in Figure 15, Model 6160030 and 6160047:
1. ID/Lot Number
Label in Figure 16, Model 6160030 and 6160047:
1. Maximum distance allowed between system cable and harness attachment point is 9 inches (23 cm).
2. Do not use with Lanyard.
To Next Page
Loading...
Need help?
General
