ABB ACS550-01 - Page 58

58 ACS550 User’s Manual
Start-Up
2503 CRIT SPEED 1 HI 0…30000 rpm / 0…500 Hz 1 rpm / 0.1 Hz 0 rpm / 0 Hz
2504
CRIT SPEED 2 LO 0…30000 rpm / 0…500 Hz 1 rpm / 0.1 Hz 0 rpm / 0 Hz
2505 CRIT SPEED 2 HI 0…30000 rpm / 0…500 Hz 1 rpm / 0.1 Hz 0 rpm / 0 Hz
2506
CRIT SPEED 3 LO 0…30000 rpm / 0…500 Hz 1 rpm / 0.1 Hz 0 rpm / 0 Hz
2507
CRIT SPEED 3 HI 0…30000 rpm / 0…500 Hz 1 rpm / 0.1 Hz 0 rpm / 0 Hz
Group 26: Motor Control
2601
FLUX OPTIMIZATION 0 = OFF, 1 = ON 10
2602 FLUX BRAKING 0 = OFF, 1 = ON 10
2603
IR COMP VOLT 0…100 V 1 size dependent
2604
IR COMP FREQ 0…100% 1 80%
2605 U/F RATIO 1 = LINEAR, 2 = SQUARED 11
2606
SWITCHING FREQ 1,4,8, 12 kHz - 4 kHz
2607
SW FREQ CTRL 0 = OFF, 1 = ON -1
2608
SLIP COMP RATIO 0…200% 1 0
2609
NOISE SMOOTHING 0 = DISABLE, 1 = ENABLE 10
Group 29: Maintenance Trig
2901 COOLING FAN TRIG 0.0…6553.5 kh 0.1 kh 0.0 (NOT SEL)
2902
COOLING FAN ACT 0.0…6553.5 kh 0.1 kh 0.0 kh
2903
REVOLUTION TRIG 0…65535 MRev 1 MRev 0 (NOT SEL)
2904 REVOLUTION ACT 0…65535 MRev 1 MRev 0 MRev
2905
RUN TIME TRIG 0.0…6553.5 kh 0.1 kh 0 (NOT SEL)
2906
RUN TIME ACT 0.0…6553.5 kh 0.1 kh 0.0 kh
2907 USER MWH TRIG 0.0…6553.5 MWh 0.1 MWh 0 (NOT SEL)
2901
USER MWH ACT 0.0…6553.5 MWh 0.1 MWh 0.0 MWh
Group 30: Fault Functions
3001 AI<MIN FUNCTION 0…3 1 0
3002
PANEL COMM ERR 1…3 1 1
3003
EXTERNAL FAULT 1 0…6, -1…-6 1 0
3004 EXTERNAL FAULT 2 0…6, -1…-6 1 0
3005
MOT THERM PROT 0 = NOT SEL, 1 = FAULT, 2 = WARNING 11 (FAULT)
3006
MOT THERM TIME 256…9999 s 1 500 s
3007
MOT LOAD CURVE 50…150% 1 100%
3008
ZERO SPEED LOAD 25…150% 1 70%
3009
BREAK POINT FREQ 1…250 Hz 1 35 Hz
3010
STALL FUNCTION 0…2 1 0 (NOT SEL)
3011
STALL FREQUENCY 0.5…50 Hz 0.1 Hz 20 Hz
3012
STALL TIME 10…400 s 1 s 20 s
3013
UNDERLOAD FUNC 0 = NOT SEL, 1 = FAULT, 2 = WARNING -0 (NOT SEL)
3014
UNDERLOAD TIME 10…400 s 1 s 20 s
3015
UNDERLOAD CURVE 1…5 1 1
3017
EARTH FAULT 0 = DISABLE, 1 = ENABLE 11 (ENABLE)
3018
COMM FAULT FUNC 0 = NOT SEL, 1 = FAULT, 2 = CONST SP7,
3 =
LAST SPEED
1 0 (NOT SEL)
3019
COMM FAULT TIME 0…60.0 s 0.1 s 3.0 s
3021
AI1 FAULT LIMIT 0…100% 0.1% 0%
Code Name Range Resolution Default User S