ABB HT576667 - Figures

Operation Manual / 4 Product description / A100-M axial
Figures
© Copyright 2017 ABB. All rights reserved. HZTL4033_DE Revision B December 2017
Figures
Fig.1: Layout and function ........................................... 4
Fig.2: Connection of the compressor wheel cooling.... 5
Fig.3: Warning plates on the turbocharger .............. 6
Fig.4: Locations of the rating plates .......................... 7
Fig.5: Turbocharger suspension points.................... 8
Fig.6: Turbocharger suspension points.................... 9
Fig.7: Removing the foot mounting.......................... 10
Fig.8: Loosening the clamping nut ........................... 11
Fig.9: Turbocharger suspension points................... 12
Fig.10: Removing auxiliary screw .............................. 13
Fig.11: Compressor-end foot ..................................... 14
Fig.12: Turbine-end foot.............................................. 14
Fig.13: CE foot contact surface ................................. 15
Fig.14: TE foot: Handling of cup spring contact sur-
face / foot contact surface ......................................... 15
Fig.15: Tightening the foot bolts (1) ......................... 16
Fig.16: Tightening the clamping nut (2)................... 17
Fig.17: Lubricating oil pressure measuring point .. 21
Fig.18: Speed measurement....................................... 23
Fig.19: Noise insulation, bellows ............................... 27
Fig.20: Cleaning the filter silencer (1)....................... 33
Fig.21: Cleaning the filter silencer (2) ...................... 35
Fig.22: Cleaning the slotted diffuser ....................... 36
Fig.23: Turbine and nozzle ring cleaning cycle....... 43
Fig.24: Procedure Wet cleaning of turbine and
nozzle ring...................................................................... 43
Fig.25: Assemblies........................................................ 51
Fig.26: Removing / installing the filter silencer .... 52
Fig.27: Removing / installing the air suction branch ... 53
Fig.28: Axial clearance ................................................ 54
Fig.29: Removing wall insert ..................................... 55
Fig.30: Transporting and turning wall insert......... 56
Fig.31: Removing the diffuser .................................... 57
Fig.32: Remove compressor casing ......................... 58
Fig.33: Safety-relevant screws ................................... 59
Fig.34: Removing cartridge group 1.......................... 60
Fig.35: Removing cartridge group 2.......................... 61
Fig.36: Removing turbine diffuser 1.......................... 62
Fig.37: Removing turbine diffuser 2.......................... 62
Fig.38: Removing cover ring 1 .................................... 63
Fig.39: Removing cover ring 2 .................................... 63
Fig.40: Removing nozzle ring 1................................... 64
Fig.41: Removing nozzle ring 2................................... 64
Fig.42: Installing nozzle ring 1 .................................... 65
Fig.43: Installing nozzle ring 2 .................................... 66
Fig.44: Installing cover ring ........................................ 67
Fig.45: Installing turbine diffuser 1 ........................... 68
Fig.46: Installing turbine diffuser 2........................... 68
Fig.47: Installing the cartridge group 1 .................... 69
Fig.48: Installing the cartridge group 2.................... 70
Fig.49: Preparing the threaded stud (25008) .......... 71
Fig.50: Fitting the spinner nose cone(25012) ........ 72
Fig.51: Installing the cartridge group 3 .................... 73
Fig.52: Installing the compressor casing ................. 74
Fig.53: Installing diffuser ............................................ 75
Fig.54: Turning and moving in wall insert................ 76
Fig.55: Fitting the wall insert...................................... 77
Fig.56: Axial clearance.................................................. 78
Fig.57: Removing the nozzle ring at the turbine end.. 80
Fig.58: Installing the nozzle ring at the turbine end.... 81
Fig.59: Tightening torques 1 ...................................... 82
Fig.60: Tightening torques 2...................................... 82
Fig.61: Flange tightening sequence .......................... 84
Fig.62: Fitting the locking device .............................. 87
Fig.63: Cover plate (01) / spacer sleeves (02) dimen-
sions ................................................................................. 89
Fig.64: Fitting the cover plate.................................... 90
Fig.65: Turbocharger with part numbers ................ 96
Page 98 / 99Page 98 / 99