ABB TZIDC Manual

48 pages

To Next Page

To Previous Page

14 TZIDC, TZIDC-200 DIGITAL POSITIONER | COI/TZIDC/TZIDC-200-EN REV. B

… 3 Configuration

HART parameter overview (graphic)

Figure 2: HART® Parameter Overview

Table of Contents2
Safety4
General Information and Instructions4
Warnings4
Intended Use4
Improper Use4
Cable Glands4
Warranty Provisions4
Cyber Security Disclaimer5
Software Downloads5
Manufacturer's Address5
Service Address5
Operation6
Safety Instructions6
Parameterization of the Device6
Menu Navigation6
Menu Levels7
Operating Modes7
Operating Mode 1.0: Control with Adaptation7
Operating Mode 1.1: Control Without Adaptation7
Operating Mode 1.2: Manual Adjustment in the Stroke Range8
Operating Mode 1.3: Manual Adjustment in the Sensor Range8
Locks9
Configuration10
General Information10
Example10
Parameter Description HART11
HART Parameter Overview (Graphic)14
Parametergroup 1: Standard15
ACTUATOR - Actuator Type15
AUTO_ADJ - Automatic Adjustment15
ADJ_MODE - Automatic Adjustment Mode16
TEST - Test16
FIND_DEV - Find Device17
EXIT - Back to Work Level17
Parameter Group 2: Set Point17
MIN_RGE - Min. Set Point Range17
MAX_RGE - Max. Set Point Range17
CHARACT - Characteristic Curve18
ACTION - Direction of Action (Setpoint Signal)18
SHUT_CLS - Shut-Off Value 018
SHUT-OPN - Shut-Off Value 10018
RAMP up - Set Point Ramp (Up)19
RAMP DN - Set Point Ramp (Down)19
EXIT - Back to Work Level19
Parameter Group 3: Working Range20
MIN_RGE - Min. Operating Range20
MAX_RGE - Max. Operating Range20
ZERO_POS - Zero Point Position21
EXIT - Back to Work Level21
Parameter Group 4: Messages22
TIME_OUT - Stroke Time Monitoring22
POS_SW1 - Switching Point SW122
POS_SW2 - Switching Point SW222
SW1_ACTV - Active Direction SW123
SW2_ACTV - Active Direction SW223
EXIT - Back to Work Level23
Parameter Group 5: Alarms24
LEAKAGE - Leakage to Actuator24
SP_RGE - Set Point Monitoring24
SENS_RGE - Operating Range Up-Scaled24
CTRLER - Controller Inactive24
TIME_OUT - Stroke Time Monitoring25
STRK_CTR - Movement Counter25
TRAVEL - Travel Counter25
EXIT - Back to Work Level25
Parameter Group 6: Manual Adjustment26
MIN_VR - Min. Working Range26
MAX_VR - Max. Operating Range26
ACTUATOR - Actuator Type27
SPRNG_Y2 - Spring Action (Y2)27
DANG_DN - Dead Angle Close27
DANG_UP - Dead Angle Open27
BOLT_POS - Actuator Bolt Position27
EXIT - Back to Work Level28
Parameter Group 7: Controller Parameters28
KP up - KP Value (Up)28
KP DN - KP Value (Down)29
TV up - TV Value (Up)29
TV DN - TV Value (Down)29
Y-OFS up - y Offset (Up)30
Y-OFS DN - Offset (Down)30
TOL_BAND - Tolerance Band31
DEADBAND - Dead Band31
DB_APPR - Deadband Approach31
DB_CALC - Deadband Determination31
LEAK_SEN - Leak Sensitivity32
EXIT - Back to Work Level32
Parameter Group 8: Analog Output32
MIN_RGE - Current Range Min32
MAX_RGE - Current Range Max32
ACTION - Direction of Action of the Characteristic Curve32
ALARM - Alarm33
RB_CHAR - Calculate Back to Characteristic33
TEST - Test33
ALR_ENAB - Alarm through the Analog Output33
CLIPPING - Extending the Signal Output Range33
EXIT - Back to Work Level34
Parameter Group 9: Digital Output34
ALRM_LOG - Alarm Output Logic34
SW1_LOG - Logic34
SW2_LOG - Logic35
ALARM DO - Logic35
EXIT - Back to Work Level35
Parameter Group 10: Digital Input36
FUNCTION - Digital Input Function Selection36
EXIT - Back to Work Level37
Parameter Group 11: Safety Position37
FAIL_POS - Safety Position37
FACT_SET - Factory Setting38
IP-TYP - Type of I/P Module38
IP_COMP - IP Compensation38
HART_REV - HART® Revision39
EXIT - Back to Work Level39
Diagnosis / Error Messages40
Error Codes40
Alarm Codes42
Message Codes43
Error Handling44
Positioner Oscillates44
Positioner Without Function45

Other manuals for ABB TZIDC

Operating Instructions88 pages

Commissioning Instruction60 pages

Commissioning Instructions72 pages

Service Instruction4 pages

Questions and Answers:

Need help?

Do you have a question about the ABB TZIDC and is the answer not in the manual?

ABB TZIDC Specifications

General

Input Signal	4 to 20 mA
Communication Protocol	HART
Protection Class	IP66, NEMA 4X
Enclosure Rating	IP66, NEMA 4X
Operating Temperature	-40 to 85 °C
Material	Aluminum
Mounting	Linear or rotary actuators
Housing Material	Aluminum
Weight	1.5 kg
Supply Pressure	1.4-7 bar (20-100 psi)