To Next PageTo Next PageWhy is the outdoor temperature flashing or showing dashes on my ACU-RITE 01022 Weather Station?
The outdoor temperature might be flashing or showing dashes on your ACU-RITE Weather Station due to wireless interference. To resolve this, check that the A-B-C switch in the battery compartments of the display and both sensors are set to the same letter (A, B, or C). Changing to a different channel sometimes helps.
Why are my ACU-RITE 01022 Weather Station temperature and humidity readings inaccurate?
Inaccurate temperature or humidity readings on your ACU-RITE Weather Station can occur if the display and 5-in-1 sensor are near heat or moisture sources. Ensure both are placed away from such sources. Also, the 5-in-1 sensor should be mounted at least 1.5 m (5 ft) off the ground. You can also calibrate the indoor and outdoor temperature and humidity.
What to do if my ACU-RITE 01022 Weather Station is not measuring rainfall?
If your ACU-RITE Weather Station isn't measuring rainfall, first check that the rain gauge stabilizer (plastic tab) has been removed from the bottom of the sensor. Also, clear any debris, such as leaves, from the rain collector funnel and debris screen. Finally, calibrate the Rain Gauge.
Why are the wind readings on my ACU-RITE Weather Station inaccurate?
Inaccurate wind readings on your ACU-RITE Weather Station can be influenced by several factors. Consider what the wind reading is being compared to; professional weather stations are typically mounted at 30 ft (9 m) or higher, so compare data with a sensor at a similar height. Check the sensor's location to ensure it's mounted at least 5 ft (1.5 m) in the air with no obstructions nearby. Also, make sure the wind cups are spinning freely; if they hesitate, try lubricating them with graphite powder or spray lubricant.
What to do if my ACU-RITE 01022 display screen is not working?
If your ACU-RITE Weather Station display screen isn't working, ensure the power adapter is correctly plugged into both the display and a working electrical outlet. If it still doesn't work, reset the display by pressing and releasing the RESET button located in the battery compartment. Note that after a reset, you will need to re-enter the time and date.
Why is my ACU-RITE 01022 Weather Station forecast inaccurate?
An inaccurate forecast on your ACU-RITE Weather Station might be due to several reasons. The weather forecast icon predicts conditions for the next 12 to 24 hours, not current conditions. Also, check if the Learning Mode icon has disappeared from the display, as Learning Mode must complete before the forecast and pressure will be accurate. Allow the unit to run continuously for 33 days, as battery removal or resetting the display will restart Learning Mode. After 14 days, the forecast should be fairly accurate, but Learning Mode calibrates for a total of 33 days.
What does it mean when the Interference Indicator is flashing on my ACU-RITE Weather Station?
If the Interference Indicator is flashing on your ACU-RITE Weather Station, try relocating the lightning sensor. Also, ensure the lightning sensor is at least 3 feet (.9 m) away from electronics that may cause interference.
General| Display Type | LCD |
|---|---|
| Humidity Range | 1% to 99% |
| Power Source | Battery-powered |
| Wireless Range | 330 feet (100 meters) |
| Features | Atomic Clock |
Instructions for removing protective film from the LCD screen before first use.
A detailed list of all components included in the product packaging.
Information on how to register the product online for warranty service.
Describes the integrated hanger for convenient placement of the lightning sensor.
Indicates when the sensor is actively transmitting data to the companion unit.
Alerts the user when wireless interference affects the sensor's operation.
Allows synchronization by matching the sensor's ID code with the display.
Visually indicates when a lightning strike has occurred within a 25-mile radius.
Location for installing batteries to power the lightning sensor.
The component designed to collect and channel rainwater for measurement.
Converts sunlight into power to operate the internal aspirating fan.
Circulates ambient air to reduce solar radiation heating for better temperature readings.
Used to match the sensor's ID code with the display for unit synchronization.
The section where batteries are inserted to power the 5-in-1 sensor.
Internal sensors responsible for measuring ambient temperature and humidity.
The component that measures the speed of the wind.
The part that points into the wind to indicate wind direction.
The bracket used to secure the 5-in-1 sensor to a mounting surface.
A filter pre-installed to prevent debris from entering the rain gauge.
Buttons like '>', 'select', '^', 'v', 'options', 'alarms', 'records', 'clear' for interacting with the display.
Used for confirming selections and navigating through setup preferences.
Adjusts the display's backlight brightness or activates it momentarily.
A built-in hole designed for mounting the display unit on a wall.
Ensures proper synchronization between the display and outdoor sensors.
Resets the unit to its original factory settings.
Controls display brightness when powered by adapter or backlight when on battery.
Guides on setting the A-B-C switch for sensor and display synchronization.
Instructions for installing batteries, recommending alkaline or lithium types.
Setting the A-B-C switch to match the display and lightning sensor for synchronization.
Instructions for installing batteries, recommending alkaline or lithium types for best performance.
Removing the plastic tab to enable the rain gauge functionality.
Guides on setting the A-B-C switch to match outdoor sensors for proper unit synchronization.
Instructions for connecting the power adapter for primary operation.
Details on installing optional backup batteries to preserve data during power loss.
Step-by-step guide to setting the clock, date, and measurement units.
Information on adjusting backlight brightness levels and auto-dim mode.
Recommendations for placing the display in a dry, dust-free area away from direct sunlight.
Guidance on positioning the 5-in-1 sensor outdoors for accurate measurements.
Best practices for placing the lightning sensor outdoors for optimal performance.
Key guidelines to maximize wireless range and prevent interference.
Explains how to identify and resolve false lightning detection due to interference.
Lists common electronic devices that can cause interference with the sensor.
Details on optimal installation height and mounting options for the 5-in-1 sensor.
Instructions for orienting the solar cell to face south for maximum sun exposure.
Explains the learning mode for determining altitude and calibrating forecasts.
Details AcuRite's self-calibrating forecasting and its accuracy.
How to manually change displayed readings like wind chill, dew point, and heat index.
Explains how current, average, and peak wind speeds are displayed and calculated.
Describes how barometric pressure and trending indicators are displayed.
Details lightning strike detection, reporting, and associated icons.
Information on expanding the system with optional temperature and humidity sensors.
How to view readings from indoor and add-on sensors.
Explains how to track and view historical rainfall accumulation data.
Describes the ticker that displays real-time weather information and alerts.
Details on viewing daily, weekly, and monthly high/low temperature and humidity records.
Information on setting custom alarms for various weather categories.
Step-by-step instructions for setting up new weather alarms with low and high thresholds.
Procedures for disabling individual alarms or all alarms at once.
Solutions for when the 5-in-1 or lightning sensor is not received by the display.
Addressing issues where outdoor temperature is flashing or showing dashes.
Troubleshooting steps for improving the accuracy of the weather forecast.
Steps to resolve inaccuracies in indoor and outdoor temperature and humidity readings.
Solutions for when the rain gauge is not recording rainfall accurately.
Tips for troubleshooting and improving the accuracy of wind speed and direction readings.
Steps to take if the display screen fails to operate or shows errors.
Solutions for when add-on sensors are not recognized by the display unit.
Guidance on addressing the flashing interference indicator on the sensor.
Instructions for cleaning the display unit safely and effectively.
Guidance on cleaning and maintaining the 5-in-1 sensor, including insect prevention.
Recommended cleaning procedures for the lightning sensor.
How to calibrate indoor/outdoor temperature, humidity, and barometric pressure readings.
Step-by-step guide to calibrate the rain gauge for accurate rainfall measurement.
Methods for adjusting the rain gauge calibration screws for precise readings.
Lists the technical specifications for temperature, humidity, wind speed, and more.
Information regarding FCC compliance and potential interference.
Contact methods and information for obtaining customer support for the product.
Details the terms, conditions, and limitations of the product's one-year warranty.
