AERMEC FCZ-ACT - General Warnings; Installation

IT EN FR DE ES
12 IFCZ-ACTALJ 1807- 4696520_04
GENERAL WARNINGS
• WARNINGS REGARDING SAFETY AND INSTALLATION STANDARDS
• Follow the indications below to install the equipment correctly. The
completion of all operations, according to specic requirements, is left to
the experience of the installer.
• Do not modify or tamper with the units, as dangerous situations can
occur. The manufacturer will not be liable for any damage caused. The
validity of the warranty shall be void in the event of failure to comply
with the indications mentioned in this manual.
• Before starting any operations, READ THESE INSTRUCTIONS CAREFULLY
AND CARRY OUT THE SAFETY CHECKS TO AVOID ALL RISKS.
• All the sta involved must have thorough knowledge of the operations
and any danger that may arise when the installation operations are
carried out.
• The unit must be installed to facilitate routine (lter cleaning) and special
maintenance operations.
•
ATTENTION: the fan coil is connected to the power supply and the
hydraulic circuit. Operations performed by persons who do not have the
required technical skills can lead to personal injury to the operator or
damage the unit and the surrounding environment.
•
ATTENTION: The unit must be installed in compliance with national
regulations.
•
ATTENTION: make sure that the power supply has been disconnected
before carrying out any interventions.
•
ATTENTION: Install a device, master switch or electric plug that allows
the unit’s power supply to be completely disconnected.
•
ATTENTION: In order to protect the unit against short circuits, mount
a magnet circuit breaker omnipolar switch on the power supply line. In
order to avoid any danger due to the accidental rearming of the thermal
cut-out device, this appliance must not be powered with an external
switching device, such as a timer, or be connected to a circuit that is
regularly powered or disconnected from the service.
•
ATTENTION! DANGER! Any use other than what is indicated by
Aermec is prohibited.
•
Supply the fan coil only with the voltage value indicated in the data
plate
• The fan coil may be permanently damaged if a dierent electric power
supply is used.
•
OPERATION ANOMALIES
• In the event of operation anomalies, power o the unit and then power
it back on and re-start the unit.
• Do not try to repair the unit on your own, as it may be very dangerous!
• If the problem persists, call the Area After-sales Service immediately.
•
Do not pull the electric cable
• It is very dangerous to pull, step on or crush the power supply cable or
secure it using nails or staples.
• The damaged cable can cause short circuits and injury to persons.
•
Electric power supply cable
• If the power supply cable is damaged, it must be replaced with a
new cable of adequate section. Have the repair made by "Qualied
personnel", in order to prevent any risk.
• Do not repair damaged cables.
• For the electric power supply, use integral cables with suitable section
for the load.
•
Do not introduce objects into air vents
• Do not introduce any objects into the air outlet slots.
• This could cause injury to persons or damage the fan.
•
INFORMATION
•
• The FCZ AERMEC units are constructed according to the recognised
technical standards and safety regulations. They have been designed and
must be used for air conditioning and heating purposes, in accordance
with their technical features.
• Any contractual or extra-contractual liability of the Company is excluded
for injury/damage to persons, animals or objects owing to installation,
regulation and maintenance errors or improper use. All uses not
expressly indicated in this manual are prohibited.
• Use suitable Personal Protective Equipment (PPE) during installation,
maintenance, and cleaning stages.
• Do not use the unit as storage for equipment or spare parts. Any use
other than that indicated in this manual is prohibited as it can generate
dangerous situations.
• ATTENTION: the electric and hydraulic connections, together with
installation of the fan coils and their accessories must only be performed
by technicians who have the technical-professional requisites for
installation, transformation, extension and maintenance of the systems
and who can verify these functions in terms of safety and functionality (in
accordance with the national laws in force in the country of installation).
In this manual they will be also identied as: experienced and qualied
technician with specic technical knowledge.
• Aermec will not be liable for damage due to failure to follow these
instructions.
• Make sure the unit has not been damaged during transport before
installation.
• using a damaged machine could be dangerous.
• the support surface must withstand the weight of the unit.
• Note:
• Always indicate the serial number for future reference and for
any communication with AERMEC S.p.A.
• STORING THE DOCUMENTATION
• Hand over the instructions with all the related documentation to
the system user, who must store the instructions so that they are
always available in case of necessity.
TRANSPORT
• Refer to the weight indications on the data plate to transport the unit
safely.
• Take the following measures during transport:
• The unit and the accessories must not undergo violent impacts in order
not to aect the integrity of the structure and of the internal components;
• during transportation, the unit and any accessories must be protected in
order to prevent impacts, for this reason they must be properly secured
on the transportation oor with ropes or any other means that prevent
their movement;
• during transport and storage, the unit and the accessories must always
be protected against bad weather.
VERIFICATIONS UPON RECEPTION
• Visually check the unit upon reception to make sure that:
• the order corresponds with what is indicated in the transport documents;
• packaging is intact;
• the unit is intact;
• all the components have been provided.
• Indicate any damage or missing components on the transport
document.
HANDLING
• ATTENTION! : Wear proper personal protective equipment (PPE) during
handling operations.
• Fully remove the unit and the components from the packaging before
installation and use.
INSTALLATION
• Read this sheet carefully; the execution of all works must be performed
by experienced and qualied sta with specic technical skills, according
to Standards in force on this subject in the installation country.
• Comply with the installation instructions provided in the following
paragraphs. The paragraphs follow a chronological order to facilitate
installation.
• Retrieve the documents (manuals and declarations of conformity) and