13
1. Order the 82357B USB/GPIB interface to control a power meter by the
E5071C.
Additional Accessories
Power limiters
□
N9355B power limiter, 10 dBm limiting threshold,
10 MHz to 18 GHz, Type-N
□
N9356B power limiter, 25 dBm limiting threshold,
10 MHz to 18 GHz, Type-N
□
N9355C power limiter, 10 dBm limiting threshold,
10 MHz to 26.5 GHz, 3.5 mm
□
N9356C power limiter, 25 dBm limiting threshold,
10 MHz to 26.5 GHz, 3.5 mm
DC blocks
□
N9398C DC block, 16 V maximum working voltage,
50 kHz to 26.5 GHz, 3.5 mm
□
N9399C DC block, 50 V maximum working voltage,
700 kHz to 26.5 GHz, 3.5 mm
□
11742A, 50 V maximum working voltage, 45 MHz to
26.5 GHz, 3.5 mm
Amplifiers
□
87405B pre-amplifi er, 22 dB gain, 10 MHz to 4 GHz
□
87405C pre-amplifi er, 25 dB gain, 100 MHz to 18 GHz
□
87415A amplifi er, 25 dB gain, 2 to 8 GHz
□
83006A amplifi er, 20 dB gain, 10 MHz to 26.5 GHz
Attenuators
□
8491A fi xed attenuator, DC to 12.4 GHz, Type-N
□
8493A fi xed attenuator, DC to 12.4 GHz, SMA
RF & microwave switches
□
N1810TL SPDT switch, terminated, DC to 26.5 GHz
□
N1810UL SPDT switch, unterminated, DC to 26.5 GHz
□
87104B SP4T switch, terminated, DC to 20 GHz
□
87106B SP6T switch, terminated, DC to 20 GHz
□
87222C transfer switch, DC to 26.5 GHz
□
L7104B SP4T switch, terminated, DC to 20 GHz
□
L7106B SP6T Switch, terminated, DC to 20 GHz
□
L7222C transfer switch, DC to 26.5 GHz
□
P9400C solid state PIN diode transfer switch,
100 MHz to 18 GHz
□
P9402C SPDT solid state PIN diode switch,
100 MHz to 18 GHz
□
P9404C SP4T solid state PIN diode switch,
100 MHz to 18 GHz
□
U9397C SPDT solid state FET hybrid switch,
300 kHz to 18 GHz
□
U9400C solid state FET hybrid transfer switch,
300 KHz to 18 GHz
Power meters and sensors
1
Recommended for source output power calibration.
□
E4416A single-channel EPM-P series power meter
□
E4417A dual-channel EPM-P series power meter
□
E4418B single-channel EPM series power meter
□
E4419B dual-channel EPM series power meter
□
N1911A single-channel P-series power meter
□
N1912A dual-channel P-series power meter
□
8482A power sensor, 100 kHz to 4.2 GHz, Type-N (m),
100 mW
□
E9304A-H18 power sensor, 9 kHz to 18 GHz, Type-N (m),
100 mW
□
E4412A CW power sensor, 10 MHz to 18 GHz, Type-N (m),
200 mW
□
E4413A CW power sensor, 50 MHz to 26.5 GHz,
3.5 mm (m), 200 mW
□
N1921A power sensor 50 MHz to 18 GHz, Type-N (m)
□
N1922A power sensor 50 MHz to 40 GHz, 2.4 mm (m)
Probe
□
85024A high-frequency probe, 300 kHz to 3 GHz
General accessories
System racks and cases
□
5063-9229 handle kit, may be ordered as option 1CN
(two included)
□
5063-9216 rack mount kit, for use without handles: may
be ordered as option 1CM
□
5188-4430 rack mount kit, for use with previously
supplied handles; may be ordered as option 1CP
□
E3663AC rack mount rail kit, for use with 5063-9216 or
5188-4430
□
9211-2658 transit case
Interface cables
The following GPIB cables can be used to connect the net-
work analyzer with an external device such as a computer
□
10833A GPIB cable, 1.0 m (3.3 ft)
□
10833B GPIB cable, 2.0 m (6.6 ft)
□
10833C GPIB cable, 4.0 m (13.1 ft)
□
10833D GPIB cable, 0.5 m (1.6 ft)
□
82357B GPIB to USB interface, necessary to control a
power meter or signal generator with the E5071C.
Monitors
□
XGA-compatible monitor
Printers
□
USB printers with Microsoft
®
Windows printer driver
To Next Page
Loading...
Need help?
General
