Akai AM-U61

OPERATIONS
RECORDING
DEPRESS THE POWER SWITCH TO ean ON
THE POWER.
@
RECORDING
FROM
SOURCE
MONITORING
1.
Set
the
REC
SELECTOR
to
the
desired
recording
source:
®@
To
monitor
the
source
signals,
turn
on
the
Input
switch
PHONO:
Recording
from
a
record.
corresponding
to
the
position
of
the
REC
SELECTOR.
For
TUNER:
Recording
a
radio
broadcast.
example,
if
recording
from
a
record,
turn
on
the
PHONO
AUX:
Recording
from
an
equipment
connected
to
the
switch.
AUX
jacks.
@
During
recording,
to
monitor
an
equipment
beside
the
2.
Put
the
tape
deck(s)
into
recording
standby
mode.
source
equipment,
turn
on
the
Input
switch
corresponding
3.
Play
back
the
source
equipment
and
adjust
the
tape
deck(s)’s
to
the
desired
equipment.
For
example,
you
can
monitor
recording
level.
a
radio
broadcast
while
recording
from
a
record
just
by
4.
Set
the
source
equipment
ready
to
play
back
from
the
be-
turning
on
the
TUNER
switch.
ginning.
®
Comparison
of
the
source
signals
to
the
just
recorded
signals
5.
Play
back
the
source
equipment
and
put
the
tape
deck(s)
Possible
only
with
a
3-head
tape
deck(s).
into
recording
mode.
1.
Set
the
Tape
Monitar
switch
of
the
tape
deck(s)
to
the
Tape
*
The
VOLUME,
BALANCE,
BASS
and
TREBLE
controls
position.
can
be
adjusted
and
the
SUBSONIC
and
LINE
STRAIGHT
2.
Turn
on
the
TAPE-1
or
-
+2
switch
to
monitor
the
just
record-
switches and MUTING and LOUDNESS buttons can be set ed signals.
during
recording
but
they
will
have
no
effect
on
the
record-
3.
Turn
on
the
Input
switch
corresponding
to
the
source
ing
signals,
equipment
to
monitor
the
source
signal.
LEFT TAPE 2 REC LEFT LINE IN
Source RIGHT TAPE 2 REC RIGHT LINE IN
LEFT
TAPE 1 LEFT
REC LINE IN
RIGHT RIGHT
TAPE 1 LINE IN
REC
TAPE 1 and/or TAPE 2
PLAYBACK
MODE
iT
°ECORDING
MODE
@ TAPE DUBBING
From TAPE-1 to TAPE-2
1. Set the REC SELECTOR to DUBBING 1 > 2. 6. Play back the playback tape deck and put the recording
2. Put the tape deck connected to the TAPE-2 jacks to record- tape deck into recording mode.
ing standby mode. * If using a 3-head tape deck for recording, turn on the
3. Put the tape deck connected to the TAPE-1 jacks to play- TAPE-2 switch to monitor the just recorded signals and turn
back mode. on the TAPE-1 switch to monitor the source signals.
4.
Adjust
the
recording
tape
deck’s
recording
input
levels.
*
Dubbing
can
also
be
done
from
a
tape
deck
connected
to
the
5.
Set
the
playback
tape
deck
ready
to
play
back
from
the
TAPE
2
jacks
to
a
tape
deck
connected
the
TAPE
1
jacks.
beginning. in this case, set the REC SELECTOR to DUBBING 2 > 1.
LEFT
TAPE 2 LEFT
REC LINE IN
CEE LEFT
LINE TAPE 1
OUT PLAY
RIGHT RIGHT 3
LINE
TAPE
1
AM-U61
TAPE
2
LINE
IN
OUT
PLAY
REC
PLAYBACK
MODE
>
RECORDING
MODE