Alcatel-Lucent OmniSwitch 6860 - PoE Chassis Details and Specifications

OmniSwitch OS6860/OS6900/OS10K Troubleshooting Guide Part No.032996-00 Rev.A
AOS Release 7.X and 8.X January 2015
Alcatel-Lucent Page 34 of 148
Legend: Mac Address: * = address not valid,
Mac Address: & = duplicate static address,
Domain Vlan/SrvcId/ISId Mac Address Type Operation Interface
-----------+---------------------+-------------------+---------------+------------+----------
VLAN 10 00:13:72:19:5e:1f dynamic bridging 2/1/16
5.3. bShell Troubleshooting
Warning:
Maintenance Shell commands should only be used by Alcatel-Lucent personnel or under the direction of Alcatel-
Lucent. Misuse or failure to follow procedures that use Maintenance Shell commands in this guide correctly can
cause lengthy network down time and/or permanent damage to hardware.
If a problem is specific to a NI and the MAC address is not being learned by the switch, the first step is to
verify from the the NI that the MAC address has been learned. There is a possibility that the NI has learned the
MAC but CMM is not reporting that MAC because of lost IPC messages between the CMM and NI.
The “l2 show” command will dump all of the MAC addresses. Check the “show mac-learning summary”
command to confirm how many mac-addresses are present befoare using the “l2 show” command.
6860-> su
Entering maintenance shell. Type 'exit' when you are done.
SHASTA #-> bshell
Entering character mode
Escape character is '^]'.
BCM.0> l2 show
mac=00:0a:1e:22:02:51 vlan=4094 modid=4 port=0 Hit
mac=00:13:72:19:5e:1f vlan=10 modid=4 port=16 Hit
mac=e8:e7:32:00:ef:a2 vlan=10 modid=4 port=7 Hit
mac=e8:e7:32:b3:49:26 vlan=1 modid=4 port=16 Hit
mac=e8:e7:32:b3:49:27 vlan=1 modid=4 port=15 Hit
mac=00:0a:1e:22:01:f8 vlan=4094 modid=0 port=0/cpu0 Hit CPU
mac=01:20:da:99:99:99 vlan=1 modid=0 port=0/cpu0 Static CPU MCast=1
mac=e8:e7:32:00:ef:a2 vlan=1 modid=4 port=7 Hit
mac=00:0a:1e:22:02:f8 vlan=4094 modid=4 port=0 Hit
mac=e8:e7:32:00:ef:a2 vlan=30 modid=4 port=7 Hit
Mac-Address Lookup in bShell:-
OS6900 / OS10K bShell command to search for a MAC address in the hardware.
6900-> su
Entering maintenance shell. Type 'exit' when you are done.
TOR #-> bshell
Entering character mode
Escape character is '^]'
BCM.0>sear l2_entry mac_addr=0x442b032ead41
Searching L2_ENTRY table indexes 0x0 through 0x7fff...
L2_ENTRY.ipipe0[4328]:
<VPG_TYPE_1=0,VPG_TYPE=0,VPG_1=0x215,VPG=0xb,VLAN_ID=0xfc,VFI=0xfc,VALID=1,T_1=1,TGID_1=0x15,TGID
=0xb,T=1,STATIC_BIT=1,SRC_DISCARD=0,SCP=0,RPE=0,REMOTE_TRUNK_1=0,REMOTE_TRUNK=0,REMOTE=0,PRI=0,PO
RT_NUM_1=0x15,PORT_NUM=0xb,PENDING=0,OVID=0xfc,MODULE_ID_1=8,MODULE_ID=0,MIRROR=0,MAC_BLOCK_INDEX
=0,MAC_ADDR=0x442b032ead41,LOCAL_SA=0,LIMIT_COUNTED=0,L3=0,L2MC_PTR=0xb,L2:VPG_TYPE=0,L2:VPG=0xb,
L2:VLAN_ID=0xfc,L2:VFI=0xfc,L2:TGID=0xb,L2:T=1,L2:STATIC_BIT=1,L2:SRC_DISCARD=0,L2:SCP=0,L2:RPE=0
,L2:REMOTE_TRUNK=0,L2:REMOTE=0,L2:PRI=0,L2:PORT_NUM=0xb,L2:PENDING=0,L2:MODULE_ID=0,L2:MIRROR=0,L
2:MAC_BLOCK_INDEX=0,L2:MAC_ADDR=0x442b032ead41,L2:LIMIT_COUNTED=0,L2:L3=0,L2:L2MC_PTR=0xb,L2:EH_T