CAREFULLY INSPECT BEFORE REAL FLIGHT .~mfjWJ8~1(;fe¥AfjfIHJ:WJffl~~~
,*Before flying, please check to make sure no one else is operating on the same frequency for the safety.
,*Before flight, please check if the batteries of transmitter and receiver are enough for the flight.
,*Before turn on the transmitter, please check if the throttle stick is in the lowest position. IDLE switch is OFF.
,*When turn off the unit, please follow the power on/off procedure. Power ON- Please turn on the transmitter
first, and then turn on receiver. Power OFF-Please turn off the receiver first and then turn off the transmitter.
Improper procedure may cause out of control, so please to have this correct habit.
,*Before operation, check every movement is smooth and directions are correct. Carefully inspect servos for
interference and broken gear.
,*Check for missing or loose screws and nuts. See if there is any cracked and incomplete assembly of parts.
Carefully check main rotor blades and rotor holders. Broken and premature failures of parts possibly cause
resulting in a dangerous situation.
,*Check all ball links to avoid excess play and replace as needed. Failure to do so will result in poor flight
stability.
,*Check the battery and power plug are fastened. Vibration and violent flight may cause the plug loose and
result out of control.
*~~mBM~~m~M~m~~~~~~T~®A,~m~MB~~®A~~~o
*~~mBMm~~~~~~m~~~~~~.~T±~~mB~~~o
*~~Mm8i[\583~~tffit~~~{j1D2~jMli ' ~~*~;;g:~~ ' ~~~~~ (IDLE)~~D2~~jlI~ 0
*~~~®~.B~m~~~~~~,~~~~~~~g~~.,~~~m~~~m:~~~~~~Mm~~.,~~~g~~~mo
~~m~~~~~~~~~~~~m.'~.B~~®A~~~,••~~m~~.o
*~~.~m~s~~~§m~~~~m.'&B~~~~m,~wm~~~~~~~~~T~~m.~M~'~mm.~~~~~.B
~~r~J3:JI~1B~~ 0
*mBMm~~~~~~.~~••~.~,m~~~mB~~.~~m~~~,gEWm~~.~~~~.'~~~m~~~.~~~
~{j1o~.~~&~~.~~~~.~.mB'~~~~~~mm~1B~o~.:~~ffi·~Rm~~~~&~m~.wm~.~tto
*WmM~~~W~~~~.~~M~'R.~~W~~~~~'~~~~~S~~m$.~~1B~o
*m~~~&~~m~~~~~~.'mB~~.~~.~~mB·~~~~~~m~.~~~~~~~1B~o
Standard Equipment~$I]G1i1§
,~
~?
II
'" I~I"I
$QO,ojBI~~
~~~
700NC
700NB
700NB1
700NB2
700NB3
700NB4
700NB5
Iii
twDJ
~
~
__ ;;=~_M".~~,
~ r;r
fr'; .
_/'
1J_~_
RCE·G600 Governor
700NH
700NG
700NT1
700NT2
I700NT3
700NZ
I RCf -G6001Ej£~
,
When you see the marks as below, please use glue or grease
to ensure flying safety.
~~Tm5m2*.§&7t~~' ~~~Gi3Lij~~L583' ~iiij~j~m2crr.~ 0
CA: Apply CA Glue to fix.
R48: Apply Anaerobics Retainer to fix.
T43: Apply Thread lock to fix.
Oil: Add Grease.
CA:j~ffl~FI!J~~~~
R48: j~fflIiIJIj~~~~ffi~~~~;E
T43: j~fflt"ll**ij'~
OIL: ~1Jm~5~5E13
When assembling ball links, make sure the "A" character
faces outside.
§m11W~~~t~~tm~Bif ' A~~~Wl9}0
Grease Green Blue Self-furnished T43 Glue width: approx. 1mm
:r~m;tB ~&<§ ~§ ifi,jFe!liW(I§Iiii'iJ T43J=!~~mtj81nm
R48 metal tubular adhesive (eg. Bearings). T43 thread lock, apply
a small amount on screws or metal parts and wipe surplus off.
When disassembling, recommend to heat the metal joint about 15
Seconds.(NOTE: Keep plastic parts away from heat.)
R48 1:'m5!E;1JIiIlI!rg~(:RO,ffi7I~)l~~j!j'U ' T431:'mt"ll**,ij~' ij~i3t"ll.~IiIJIj~
9}i~8~~@~.jJEm ' 1!)I,\~8iJ~~m:F~II*~~~. ' 6RlfFffi08iJ~D2IiIlI1m
i3g~1lI~:M~1iI!J15f.J>0 ct.! ~ij~j!:j:J:I~mjITAA5J3D
4
To Next Page
Loading...
