Allen-Bradley PowerFlex 70 - Page 224

2-196 Start-Up
Figure 2.40 PowerFlex 700 Vector Control Option Startup (6)
Flux Vector Start Up (Strt,Stop,I/O)
Start-Up
A. Dig Inputs
Select a Digital
Input:
<1.Digital In 1>
2.Digital In 2
3.Digital In 3
4.Digital In 4
5.Digital In 5
6.Digital In 6
7.Done
6-0
6-23
Go to 6-1 (B.Dig
Outputs)
Start-Up
A. Dig Inputs
Enter choice for
Digital In1 Sel
Start-Up
A. Dig Inputs
Enter choice for
Digital In2 Sel
6-24
6-25
Start-Up
A. Dig Inputs
Enter choice for
Digital In3 Sel
Start-Up
A. Dig Inputs
Enter choice for
Digital In4 Sel
Start-Up
A. Dig Inputs
Enter choice for
Digital In5 Sel
Start-Up
A. Dig Inputs
Enter choice for
Digital In6 Sel
Digital In 1
Digital In 2
Digital In 3
Digital In 4
Digital In 5
Digital In 6
Enter/
Backup
Start-Up
A. Dig Inputs
Digital Input
Config options:
<Easy Configure>
Custom Configure
More info
6-2
DigIn 5,6 = MOP
Inc, Dec?
Start-Up
A. Dig Inputs
Digital Inputs
1-4 will be set
to defaults.
6-3
Start-Up
A. Dig Inputs
Digital Inputs
1-6 will be set
to defaults.
6-4
Start-Up
A. Dig Inputs
Digital Input 3
will be set to Fwd/
Reverse.
6-20
Start-Up
A. Dig Inputs
Digital In1 set
to Run Forward.
Digital In2 set
to Run Reverse.
6-12
6-19
Start-Up
A. Dig Inputs
Digital In1 set
to Not Used.
Digital In2 set
to Run/Stop.
6-7
6-8
Custom Configure
A. Dig Inputs
Easy Configure
NoYe s
Start-Up
A. Dig Inputs
Enter choice for
Control Method
<3 wire>
2 wire
More info
6-6
2-wire 3-wire
Go to 6-1 (B. Dig
Outputs)
Start-Up
A. Dig Inputs
Is REVERSE
required from
digital inputs?
<Yes>
No
6-5
Start-Up
A. Dig Inputs
Enter choice for
Control Method
<3 wire>
2 wire
More info
6-11
Ye s
3-wire
2-wire
Done
Backup
Start-Up
A. Dig Inputs
Digital In1 set
to Stop.
Digital In2 set
to Start.
6-9
6-10
Start-Up
A. Dig Inputs
Digital In1 set
to Stop.
Digital In2 set
to Start.
6-21
6-22
Start-Up
6. Strt,Stop,I/O
This section
defines I/O
functions
including Start
and Stop.
Start-Up
6. Strt,Stop,I/O
Complete these
steps in order:
<A.Dig Inputs>
B.Dig Outputs
C.Analog Outputs
D.Done
B. Dig
Outputs
Go to 6-27
Go to 6-49
6-1
D. Done
Go to 0-1 (7. Application
Features)
C.Analog
Output
Backup
Note:
- For V/Hz mode, states 6-3 - 6-5, & 6-11 - 6-16 are not displayed.
Start-Up
A. Dig Inputs
Digital Inputs
configured for
2-wire control
no reversing
Start-Up
A. Dig Inputs
Digital Inputs
configured for
2-wire control
with reversing.
Start-Up
A. Dig Inputs
Digital Inputs
configured for
3-wire control
no reversing.
Start-Up
A. Dig Inputs
Digital Inputs
configured for
3-wire control
with reversing.
Start-Up
A. Dig Inputs
2 wire control
uses a contact
that acts as
both STOP (Open)
& Run (Closed).
3 wire control
uses 2 contacts;
one for START
& one for STOP.
6-13
6-14
6-15
6-16
6-17
6-18
More
Info..
More
Info..
No
Start-Up
A. Dig Inputs
Easy Configure
asks questions
before writing
to digital ins.
Custom Configure
allows you to
program each
digital input(s)
More
info
6-26
Start-Up
A. Dig Inputs
2 wire control
uses a contact
that acts as
both STOP (Open)
& Run (Closed).
3 wire control
uses 2 contacts;
one for START
& one for STOP.
B = Basic mode
B
B
B
B
B
BB
B
B
B
B
BB
B
BB
B