What to do if Alliance Laundry Systems Dryer has spark but no flame?
If your Alliance Laundry Systems Dryer has a spark but no flame, first ensure the gas is on. Also, check for 24 VAC at the gas valve. If the issue persists, there might be a problem with the control; in this case check the voltage between the gas valve terminal MV and GND on the control.
Why Alliance Laundry Systems ST055N Dryer valve is on but there is no spark during TFI?
If the valve is on but there's no spark during TFI in your Alliance Laundry Systems Dryer, it could be due to a shorted electrode. Another possible cause is an incorrect spark gap; ensure it's set to .094-.156 inch. Also, inspect the high voltage cable for faults or poor connections. Finally, control failure can cause this issue.
What to do if Alliance Laundry Systems ST055N flame is okay during TFI, but no flame sense after TFI?
If the flame is okay during TFI but there's no flame sense after TFI in your Alliance Laundry Systems Dryer, check the electrode position and cleanliness. Also, inspect the high voltage wire. Poor grounding at the burner or a poor flame (check flame current) can also cause this issue.
How to fix reset failure on Alliance Laundry Systems ST055N?
If you're experiencing a reset failure on your Alliance Laundry Systems Dryer, it might be because the reset switch was pressed too long; try resetting again. Another possibility is that the reset switch is shorted, in which case you should replace the switch.
What to do if Alliance Laundry Systems Dryer thermostat is on, but there is no spark or valve?
If the thermostat is on but there's no spark or valve activity in your Alliance Laundry Systems Dryer, first ensure the cable connects to the control and electrode, and that voltage is present at the gas valve. If the issue persists, the control might be bad; check the red LED for a steady on or flashing codes.
How to reset Alliance Laundry Systems ST055N Dryer control in lockout mode?
If the control in your Alliance Laundry Systems Dryer is in lockout mode, a manual reset is needed. Reset it by pushing the red lockout button or use the front end control.
What to do if the Alliance Laundry Systems Dryer control is in lockout mode?
If the control panel on your Alliance Laundry Systems Dryer is in lockout mode, you will need to manually reset it. You can do this by pushing the red lockout button or using the front end control.
Crucial safety guidelines for safe operation and maintenance.
Details on identifying specific tumble dryer models and their configurations.
Provides contact details for service, support, and parts.
General safety statements and definitions of hazard symbols (Danger, Warning, Caution).
Core safety precautions to minimize risks of fire, shock, injury, or death.
Technical data including weight, dimensions, airflow, and power ratings.
Physical dimensions for dryer series 025, 030, 035, and 055.
Specifies exhaust outlet locations and diameters for 025-055 series.
Details gas connection points for 025-055 series dryers.
Steps for inspecting the unit and its packaging before installation.
Guidelines for choosing a suitable and safe installation location.
Instructions for properly placing and leveling the dryer.
Outlines power supply, wiring, and grounding requirements for safe operation.
Essential information for connecting and operating the dryer with gas.
Guidelines for sizing and installing gas supply piping for optimal pressure.
Instructions for adjusting burner orifices based on altitude for proper combustion.
Detailed requirements for electrical connections, grounding, and wiring.
Critical steps for ensuring proper electrical grounding for safety.
Step-by-step guide for making the final electrical service connection.
Tables detailing voltage, amperage, breaker, and wire size requirements.
Critical information regarding steam pressure and pipe sizing for operation.
Guidelines for steam supply and return line installation and support.
Steps for properly installing steam traps and condensate lines.
Describes the initial state of the control when power is applied.
The state where the control awaits a coin or vend satisfaction.
How to adjust drying times using dipswitches on the control.
Tables detailing dipswitch configurations for various time settings.
General guidelines for operating the tumble dryer.
Instructions for daily cleaning of the lint screen and compartment.
Guidance on properly loading the dryer with laundry.
Operating instructions for Dual Digital Timer (QT, RQ) controls.
Overview of how the DMP control manages drying and cooling cycles.
Steps for programming custom cycles and settings on the DMP control.
Details on setting up and adjusting cylinder reversing functions.
How to adjust the air shutter for optimal combustion and efficiency.
Information on the airflow switch and its importance for safety.
Instructions for adjusting the door switch for proper operation.
How to adjust the door strike for proper door closure tension.
Routine daily checks and cleaning procedures for the dryer.
Monthly maintenance tasks to ensure proper airflow and prevent overheating.
Procedure for testing the fire suppression system every three months.
Troubleshooting guide for common starting, heating, and drying issues.
Steps for safely disconnecting and removing the dryer from service.
Information on proper disposal of the appliance according to WEEE directive.
General| Brand | Alliance Laundry Systems |
|---|---|
| Model | ST055N |
| Category | Dryer |
| Type | Tumble Dryer |
| Voltage | 208-240V |
| Amperage | 30A |
| Heating Method | Electric |
| Capacity | 55 lb |
To Next Page