What to do if Alliance Laundry Systems Dryer has spark but no flame?
If your Alliance Laundry Systems Dryer has a spark but no flame, first ensure the gas is on. Also, check for 24 VAC at the gas valve. If the issue persists, there might be a problem with the control; in this case check the voltage between the gas valve terminal MV and GND on the control.
Why Alliance Laundry Systems STT30N valve is on but there is no spark during TFI?
If the valve is on but there's no spark during TFI in your Alliance Laundry Systems Dryer, it could be due to a shorted electrode. Another possible cause is an incorrect spark gap; ensure it's set to .094-.156 inch. Also, inspect the high voltage cable for faults or poor connections. Finally, control failure can cause this issue.
What to do if Alliance Laundry Systems STT30N Dryer flame is okay during TFI, but no flame sense after TFI?
If the flame is okay during TFI but there's no flame sense after TFI in your Alliance Laundry Systems Dryer, check the electrode position and cleanliness. Also, inspect the high voltage wire. Poor grounding at the burner or a poor flame (check flame current) can also cause this issue.
How to fix reset failure on Alliance Laundry Systems Dryer?
If you're experiencing a reset failure on your Alliance Laundry Systems Dryer, it might be because the reset switch was pressed too long; try resetting again. Another possibility is that the reset switch is shorted, in which case you should replace the switch.
What to do if Alliance Laundry Systems STT30N thermostat is on, but there is no spark or valve?
If the thermostat is on but there's no spark or valve activity in your Alliance Laundry Systems Dryer, first ensure the cable connects to the control and electrode, and that voltage is present at the gas valve. If the issue persists, the control might be bad; check the red LED for a steady on or flashing codes.
How to reset Alliance Laundry Systems STT30N control in lockout mode?
If the control in your Alliance Laundry Systems Dryer is in lockout mode, a manual reset is needed. Reset it by pushing the red lockout button or use the front end control.
What to do if the Alliance Laundry Systems STT30N control is in lockout mode?
If the control panel on your Alliance Laundry Systems Dryer is in lockout mode, you will need to manually reset it. You can do this by pushing the red lockout button or using the front end control.
Manual should be kept for future reference and passed on with machine.
Installation must comply with local and national codes and standards.
Crucial safety information to minimize risks of fire, explosion, injury, or death.
Lists all applicable model numbers for the manual's content.
Provides details for contacting Alliance Laundry Systems for service or support.
Explains the meaning of DANGER, WARNING, CAUTION, IMPORTANT, and NOTE statements.
Basic precautions for safe operation, installation, and maintenance.
Technical details and dimensions for various dryer models.
Technical details and dimensions for T30 and T45 dryer models.
Steps to inspect the unit for shipping damage before installation.
Guidelines for selecting a proper installation location for the dryer.
Specifies required opening sizes for make-up air for each dryer model.
Guidelines for proper exhaust ducting to ensure efficiency and safety.
Instructions for sizing and installing gas supply piping for multiple dryers.
Procedures for adjusting burner orifices for high altitude installations.
Warnings and guidelines for safe electrical connections.
Proper grounding procedures to prevent electrical shock.
Guidelines for steam supply and return line connections and support.
Key warnings before operating the appliance.
How to use the Dual Digital Timer Control for drying cycles.
Guide to operating the Diagnostic Microprocessor Control.
How to adjust the air shutter for proper burner combustion.
Notes on airflow switch operation and potential adjustments.
Regular checks for safety and proper operation.
Procedure to test the fire suppression system every three months.
Lists common problems and their possible reasons and corrective actions.
Procedures for safely disconnecting and removing the dryer.
Information on correct disposal according to WEEE directive.
General| Brand | Alliance Laundry Systems |
|---|---|
| Model | STT30N |
| Category | Dryer |
| Type | Stack Tumble Dryer |
| Heat Source | Electric |
| Control Type | Electronic |
| Dryer Capacity | 30 lb |
To Next Page