To Next PageTo Next Page
Need help?Do you have a question about the Alliance Laundry Systems ST120FG and is the answer not in the manual?
General| Brand | Alliance Laundry Systems |
|---|---|
| Model | ST120FG |
| Category | Dryer |
| Language | English |
Essential safety precautions to follow when operating the drying tumbler to prevent fire, electric shock, injury, or death.
Details for quick access to essential information and appliance specifications.
Guidance on finding the tumbler's nameplate for model and serial number identification.
Instructions on how to obtain replacement parts or literature for the tumbler.
Provides detailed measurements for tumbler cabinets, including height, width, and depth.
Specifies the location and dimensions for exhaust thimble connections for various tumbler models.
Details the required dimensions and locations for steam inlet and outlet connections.
Provides information on the required dimensions and location for gas connections.
Outlines the location and dimensions for electrical service and steam connections.
Procedure for visually inspecting the tumbler for shipping damage upon delivery.
Lists necessary components and supplies that must be locally sourced for installation.
Guidance on safely moving and positioning the drying tumbler for installation.
Instructions for ensuring the tumbler is properly leveled for optimal operation.
Details on constructing an enclosure with proper clearance for tumbler servicing and operation.
Specifies floor load capacity requirements and preparation for tumbler installation.
Recommendations for tumbler placement considering ducting and air access.
Essential guidelines for proper exhaust venting to ensure efficiency and safety.
Information on using a main collector duct for multiple tumblers, including sizing and connection.
Requirements for providing adequate make-up air for combustion and ventilation.
Illustrates gas loop piping configurations for equalizing pressure for multiple tumblers.
Shows typical gas supply piping layouts and calculation methods for 30, 50, and 75 lb tumblers.
Illustrates gas loop piping configurations for equalizing pressure for 120 lb tumblers.
Shows typical gas supply piping layouts and calculation methods for 120 lb tumblers.
Illustrates gas loop piping configurations for equalizing pressure for 170 lb tumblers.
Shows typical gas supply piping layouts and calculation methods for 170 lb tumblers.
Guidelines for steam piping, including trap installation and insulation for safety.
Refers to wiring diagrams for steam valve electrical connections within the J-Box.
Mandatory grounding procedures to prevent electric shock and ensure safety.
Procedure for changing transformer configuration jumper for voltage compatibility.
Instructions for installing a ring ferrite to protect sensitive electronic controls.
Details electrical specifications, wire sizes, and breaker ratings for 30 lb, 28" wide tumblers.
Details electrical specifications, wire sizes, and breaker ratings for 30 lb, 31.5" wide tumblers.
Details electrical specifications, wire sizes, and breaker ratings for 50 lb tumblers.
Details electrical specifications, wire sizes, and breaker ratings for 75 lb tumblers.
Details electrical specifications, wire sizes, and breaker ratings for 120 lb tumblers.
Details electrical specifications, wire sizes, and breaker ratings for 170 lb tumblers.
Step-by-step instructions for installing a new timing cam on coin meter models.
Procedure for safely removing the existing timing cam from the machine.
Procedures for performing final checks on OPL micro-control tumbler operation.
Steps for conducting final operating checks on manual dual timer tumblers.
Final checks to ensure proper operation of coin-operated tumblers.
Adjusting the air shutter on gas burners for optimal combustion and efficiency.
Procedure for adjusting the air flow switch sensitivity on 30, 50, 75 lb tumblers.
Information on the air flow switch location and function for 120 and 170 lb tumblers.
Explanation of the air flow light function on 120 and 170 lb manual timer models.
Adjusting the cylinder door switch for proper stopping when the door is opened.
Adjusting the door switch for 120 and 170 lb tumblers to stop cylinder when door opens.
Procedure for adjusting the door strike to ensure the loading door is securely closed.
Instructions for adjusting belt tension on nonreversing belt drive models.
Guidance on adjusting chain tension for nonreversing chain drive models.
Procedure for adjusting belt tension on reversing belt drive models.
Instructions for adjusting belt tension on reversing 120 and 170 lb models.
Step-by-step guide for operating the manual dual timer tumbling machine.
Instructions for operating coin-operated tumblers, including coin drop and slide models.
Explanation of the reversing function for preventing tangling and minimizing wrinkling.
Details on using the reverse control switch to select operation mode.
Guide on selecting fabric types to set the appropriate preset temperature for drying.
Instructions on selecting Automatic, Time Dry, Special, or Custom cycles for operation.
Procedure for adjusting temperature settings and selecting between Fahrenheit and Celsius.
Instructions on how to enter and exit the Show Mode for display demonstration.
Information on testing the temperature sensor and troubleshooting sensor faults.
Procedure for daily cleaning of lint screen and compartment for optimal air circulation.
Information regarding lubrication requirements for tumbler components.
Monthly procedure for removing lint from air vents and exhaust ducts.
Three-month maintenance for cleaning lint from air vents, steam coils, and exhaust ducts.
Procedure for checking and adjusting belt tension as part of monthly maintenance.
Six-month check for loose nuts, bolts, screws, and gas/electrical connections.
Troubleshooting steps for when the tumbler fails to start.
Troubleshooting steps for when the tumbler is not heating.
Steps to diagnose why clothes are not drying properly.
