EasyManua.ls Logo

Ameri-Shred Series 1 - User Manual

Ameri-Shred Series 1
34 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Service Department: 888.270.6879
AMS-150HD/ AMS-150HD-SSD/ AMS-150-SSD
AMS-300HD/ AMS-300HD-SSD/ AMS-300-SSD
OWNER’S MANUAL
SERIES 1 HARD DRIVE
NOTICE: The informaon contained within this manual is correct at me of prinng, but due to the connuing development of prod ucts,
changes in specicaons are inevitable. Ameri-Shred reserves the right to implement such changes without prior noce.

Table of Contents

Questions and Answers

  • D
    Denise CharlesAug 7, 2025
    What to do if Ameri-Shred Series 1 Paper Shredder won't run in forward or reverse?
    • B
      Bradley RiveraAug 8, 2025
      If your Ameri-Shred Paper Shredder isn't running in either direction, here's what to check: 1. **Power:** Ensure the shredder is getting power from the supply. 2. **Key Switch:** Make sure the key switch is turned on. 3. **Fuses:** Inspect the fuses in the disconnect; replace any that have blown. 4. **Overload:** Reset any tripped overload switches in the panel. 5. **Transformer Fuse:** Check the control transformer fuse and replace if necessary. 6. **Stop Button:** Verify that the stop button isn't stuck in the 'in' position. 7. **Wiring:** Look for any loose wires on the terminal strip inside the panel, and reconnect/tighten them. 8. **Stop Button Contact Block:** Examine the contact block on the stop button for continuity; replace if defective.
  • B
    biancamartinezAug 12, 2025
    Why does my Ameri-Shred Series 1 keep overload tripping?
    • D
      Donna DaughertyAug 12, 2025
      If the overload is tripping on your Ameri-Shred Paper Shredder, consider these potential causes: * **Low Voltage:** The voltage supply might be insufficient; check the voltage. * **Current Relay Setting:** The current relay may be set too high; refer to the instructions on the previous page for proper setting. * **Motor Overheating:** The motor could be overheating; inspect the motor cooling fan for obstructions. * **Dirty Cutter-head:** The cutter-head may be dirty or lack lubrication; clean and lubricate it. * **Defective Motor:** The motor might be damaged; conduct an amperage test and consult the factory for a replacement if needed.
  • R
    Robin GutierrezAug 16, 2025
    What to do if Ameri-Shred Paper Shredder motor hums but won't turn?
    • M
      Melissa HoweAug 16, 2025
      If your Ameri-Shred Paper Shredder motor hums or buzzes but doesn't turn, it could be due to: * **Single Phasing:** One leg of the 3-phase power might be dead. Remove each fuse and check for continuity in the power supply and disconnect. * **Contactor Contacts:** The contacts in the contactor could be burned, preventing connection on one leg. Consult the factory for a replacement contactor. * **Defective Motor:** The motor itself may be defective or damaged. Consult the factory for a replacement motor.
  • N
    nreidAug 20, 2025
    How to fix Ameri-Shred Series 1 that won't turn off with STOP button?
    • J
      jeremy48Aug 20, 2025
      If your Ameri-Shred Paper Shredder won't turn off using the STOP buttons, there are a couple of potential reasons: * **Defective STOP Button:** The STOP button itself may be defective. Check its continuity (normally closed). If it's bad, replace it. * **Reversing Contactor Contacts:** The contacts in the reversing contactor might be burned together. Check each leg of the forward side of the contactor for continuity. There should be no continuity. If there is, consult the factory for a replacement part.
  • M
    Matthew ThomasAug 25, 2025
    Why is the shredding capacity low on my Ameri-Shred Paper Shredder?
    • L
      Leslie LarsonAug 25, 2025
      If your Ameri-Shred Paper Shredder's shredding capacity is low, consider the following: * **Lack of Lubrication:** The cutter-head might not be lubricated. Clean and oil the cutter-head. * **Low Voltage:** Check the voltage at the power supply to ensure it's sufficient. * **Current Relay Setting:** The current relay may be set too low. See the instructions on the previous page for adjustment.
  • E
    Elizabeth HicksAug 29, 2025
    What causes Ameri-Shred Series 1 to run in reverse but not forward?
    • B
      bradleymelanieAug 29, 2025
      If your Ameri-Shred Paper Shredder runs in reverse but not forward, the issue might be: * **Defective Forward Button:** The forward button may be defective. Check the contact block for continuity and replace if bad. * **Disconnected Wire:** A wire on the forward button could be disconnected. Check and reconnect it. * **Disconnected Wire on Current Relay:** A wire on the current relay might be disconnected. Check and reconnect. * **Stuck Current Relay:** The current relay could be stuck open. Clean the relay, free up the center spool, and check continuity. If it's bad, consult the factory for a replacement relay.
  • D
    Danielle HowellSep 2, 2025
    What to do if Ameri-Shred Paper Shredder runs forward but not in reverse?
    • J
      Jessica CampbellSep 2, 2025
      If your Ameri-Shred Paper Shredder runs in forward but not in reverse, check these potential causes: * **Defective Reverse Button:** The reverse button may be defective. Check for continuity; replace if bad. * **Disconnected Wire:** There might be a disconnected wire on the reverse button. Check and reconnect it. * **Defective Contactor Coil:** The coil in the reverse side of the contactor could be defective. Consult the factory for a replacement coil.

Ameri-Shred Series 1 Specifications

General IconGeneral
BrandAmeri-Shred
ModelSeries 1
CategoryPaper Shredder
LanguageEnglish