American Eagle SRS-65

Questions and Answers

M
Michael SpencerAug 17, 2025
Why won't my American Eagle SRS-65 build up pressure?
- D
  Dylan NelsonAug 18, 2025
  If your American Eagle Compressor won't build up pressure, it could be due to several reasons. First, ensure that the air demand isn't too high by tightening air hose clamps and repairing any air leaks. Check if the air filter is plugged and clean or replace it. Also, verify the pressure switch adjustment and readjust to specifications if needed, or replace it if faulty. Other potential causes include slow compressor speed (check hydraulic flow and pressure), a slipping drive belt (readjust and tighten), an open service valve (close it), or a stuck hydraulic manifold valve (clean or replace).
J
Jennifer BrownAug 20, 2025
What to do if American Eagle SRS-65 shuts down with air demand?
- A
  allenkevinAug 20, 2025
  Your American Eagle Compressor might shut down with air demand due to several reasons. A low oil level could be the culprit, so add compressor oil to the correct level. Check if the fan is operating correctly by inspecting the ground wire and fan switch/relay. A plugged oil filter can also cause this issue, so replace the filter if needed. Additionally, a dirty or contaminated cooler core can lead to shutdown; clean the cooler fins or remove and clean the core. Ensure that the hydraulic pressure and flow are correct by adjusting and resetting them according to specifications. Lastly, a worn hydraulic motor can cause shutdowns, so consider replacing it.
B
blairisaacAug 26, 2025
What causes American Eagle SRS-65 to over pressure?
- D
  dchenAug 26, 2025
  If your American Eagle Compressor over pressures, it could be due to a defective pressure switch, which should be replaced. Another possible cause is a leaking air control line, which needs to be checked and corrected. Additionally, a stuck inlet valve may be the issue, requiring cleaning and replacement. A restriction in the control line due to dirt or ice can also cause over-pressuring; this should be cleaned and freed up.
T
Tammy BartonAug 27, 2025
Why does American Eagle Compressor synthetic oil look milky?
- K
  Kevin LevyAug 27, 2025
  If the synthetic oil in your American Eagle Compressor has a milky appearance, it's likely due to a clogged or plugged coalescing/separator cartridge. Replace the cartridge and change the compressor oil to resolve this issue.
C
Christine FordAug 30, 2025
How to fix a noisy American Eagle SRS-65 Compressor in cold weather?
- S
  stephanie48Aug 30, 2025
  If your American Eagle Compressor is noisy or loud when starting in cold weather, it is likely due to ice buildup inside the compressor from condensation. To resolve this, engage the PTO and allow the hydraulic fluid to circulate and warm up the system before engaging the compressor.
S
Sheri Buchanan MDSep 1, 2025
What to do if there's excessive oil level in American Eagle compressor?
- G
  Gloria HuynhSep 2, 2025
  An excessive oil level in your American Eagle Compressor may be due to an internal crack inside the oil cooler. To fix this, replace the cooler, change the filters, and change the compressor oil.
L
Lisa DavisSep 4, 2025
What to do if my American Eagle SRS-65 shuts down with air demand?
- M
  Michelle RodriguezSep 4, 2025
  If your American Eagle Compressor shuts down when there's air demand, several issues could be the cause. The compressor temperature may be too high. Ensure the compressor oil level is adequate, adding oil if it's low. Check the fan operation, verifying the ground wire and fan switch/relay. Replace a plugged oil filter, and clean dirty cooler fins. If the cooler core is contaminated, remove and clean it. Also, incorrect hydraulic pressure and flow may be the issue; adjust and reset according to specifications. Finally, a worn hydraulic motor may be to blame, requiring replacement.
J
Jessica LopezSep 6, 2025
What causes my American Eagle SRS-65 Compressor to over pressure?
- R
  Randy GreenSep 7, 2025
  If your American Eagle Compressor over pressures, the issue might stem from a defective pressure switch, which should be replaced. Inspect the air control line for leaks and correct them as needed. If the inlet valve is stuck, clean and replace it. Also, check for any restrictions in the control line due to dirt or ice, and clean to free it up.
M
Mrs. Lynn PattonSep 9, 2025
How to fix a noisy American Eagle SRS-65 when starting in cold weather?
- M
  Margaret SanchezSep 9, 2025
  If your American Eagle Compressor is noisy or loud when starting in cold weather, it could be due to ice buildup inside the compressor from condensation. To address this, engage the PTO and allow hydraulic fluid to circulate and warm the system before engaging the compressor.
L
Lori LewisSep 12, 2025
Why does the synthetic oil in my American Eagle SRS-65 Compressor look milky?
- D
  David HooverSep 12, 2025
  If the synthetic oil in your American Eagle Compressor has a milky appearance, it's likely due to a clogged coalescing/separator cartridge. Replace the cartridge and change the compressor oil to resolve this issue.

Summary

Introduction to SRS-65 Compressor

Chapter 1: Safety Precautions

Safety Decals

Safety decals and their meanings for proper operation and maintenance.

Chapter 2: Specifications Overview

Chapter 3: Operating the SRS-65 Compressor

Before Start-Up Procedures

Essential checks and inspections to perform before operating the compressor.

General Operation Information

Overview of compressor activation and automatic system function.

Air Operations for SRS-65 RP and SRS-65 E

Details on how the compressor operates for specific models.

Air Operations for SRS-65 P

Details on how the compressor operates for specific models.

Important Operating Notes and Warnings

Important usage warnings and disclaimers for the compressor.

Chapter 4: Routine Maintenance

Checking the Oil Level

Procedure and intervals for checking the compressor's oil level.

Condensation Drainage Procedure

How to drain condensation from the compressor case to prevent damage.

Changing the Compressor Oil

Step-by-step guide for changing the compressor oil, including warnings.

Oil Recommendation Guidelines

Guidance on selecting the appropriate oil for the compressor.

Required Oil Specifications

Specifications and properties required for compressor oil.

Oil Filter Replacement

Procedure for replacing the oil filter and recommended intervals.

Separator Cartridge Replacement

Procedure for replacing the separator cartridge and recommended intervals.

Intake Filter Maintenance

Procedure for cleaning or replacing the air intake filter.

Belt Tension Adjustment

Specifications for belt tensioning for new and used belts.

Minimum Pressure Valve Setting

Procedure for setting the minimum pressure valve if needed.

Cooler Cleaning Procedure

Maintenance procedure for cleaning the oil coolers.

Chapter 5: Installation Guide

Component Installation Overview

General guidance for installing compressor, PTO, pump, and related items.

Electrical Connection Instructions

Instructions for wiring the compressor and associated controls.

Electric Speed Control Installation

Information on optional electric speed controls for compressor operation.

Detailed Electrical Installation Diagram

Detailed wiring diagram and circuit information for the compressor.

Temperature Gauge Installation

Procedure for installing a temperature gauge probe.

Hydraulic System Setup

Description of the hydraulic system components and operation.

Air System Configuration

Description of the air system routing and tank connection.

Compressor Pressure Switch Setup

Instructions for setting the compressor pressure switch.

Hydraulic Circuit: Single Stage Pump

Diagram of a typical hydraulic circuit for a single stage pump.

Hydraulic Circuit: Tandem (Two Part) Pump

Diagram of a typical hydraulic circuit for a tandem (two part) pump.

Hydraulic Circuit with Auxiliary Cooler

Diagram of a hydraulic circuit with an auxiliary cooler.

Chapter 6: Assembly Drawings

SRS-65 RP Compressor Assembly - PN 53887

Assembly drawing and parts list for the SRS-65RP model.

SRS-65 P Compressor Assembly - PN 53889

Assembly drawing and parts list for the SRS-65P model.

Chapter 7: Replacement Parts

Hydraulic Components and Drive Parts

List of replacement parts for hydraulic components and drive systems.

Electrical and Air Pressure Components

List of replacement parts for electrical and air pressure components.

Air and Oil Filter Components

List of replacement parts for air and oil filters.

Compressor Components

List of replacement parts for compressor components.

Chapter 8: Troubleshooting Guide

Limited Warranty Statement

Summary

Introduction to SRS-65 Compressor

Chapter 1: Safety Precautions

Safety Decals

Safety decals and their meanings for proper operation and maintenance.

Chapter 2: Specifications Overview

Chapter 3: Operating the SRS-65 Compressor

Before Start-Up Procedures

Essential checks and inspections to perform before operating the compressor.

General Operation Information

Overview of compressor activation and automatic system function.

Air Operations for SRS-65 RP and SRS-65 E

Details on how the compressor operates for specific models.

Air Operations for SRS-65 P

Details on how the compressor operates for specific models.

Important Operating Notes and Warnings

Important usage warnings and disclaimers for the compressor.

Chapter 4: Routine Maintenance

Checking the Oil Level

Procedure and intervals for checking the compressor's oil level.

Condensation Drainage Procedure

How to drain condensation from the compressor case to prevent damage.

Changing the Compressor Oil

Step-by-step guide for changing the compressor oil, including warnings.

Oil Recommendation Guidelines

Guidance on selecting the appropriate oil for the compressor.

Required Oil Specifications

Specifications and properties required for compressor oil.

Oil Filter Replacement

Procedure for replacing the oil filter and recommended intervals.

Separator Cartridge Replacement

Procedure for replacing the separator cartridge and recommended intervals.

Intake Filter Maintenance

Procedure for cleaning or replacing the air intake filter.

Belt Tension Adjustment

Specifications for belt tensioning for new and used belts.

Minimum Pressure Valve Setting

Procedure for setting the minimum pressure valve if needed.

Cooler Cleaning Procedure

Maintenance procedure for cleaning the oil coolers.

Chapter 5: Installation Guide

Component Installation Overview

General guidance for installing compressor, PTO, pump, and related items.

Electrical Connection Instructions

Instructions for wiring the compressor and associated controls.

Electric Speed Control Installation

Information on optional electric speed controls for compressor operation.

Detailed Electrical Installation Diagram

Detailed wiring diagram and circuit information for the compressor.

Temperature Gauge Installation

Procedure for installing a temperature gauge probe.

Hydraulic System Setup

Description of the hydraulic system components and operation.

Air System Configuration

Description of the air system routing and tank connection.

Compressor Pressure Switch Setup

Instructions for setting the compressor pressure switch.

Hydraulic Circuit: Single Stage Pump

Diagram of a typical hydraulic circuit for a single stage pump.

Hydraulic Circuit: Tandem (Two Part) Pump

Diagram of a typical hydraulic circuit for a tandem (two part) pump.

Hydraulic Circuit with Auxiliary Cooler

Diagram of a hydraulic circuit with an auxiliary cooler.

Chapter 6: Assembly Drawings

SRS-65 RP Compressor Assembly - PN 53887

Assembly drawing and parts list for the SRS-65RP model.

SRS-65 P Compressor Assembly - PN 53889

Assembly drawing and parts list for the SRS-65P model.

Chapter 7: Replacement Parts

Hydraulic Components and Drive Parts

List of replacement parts for hydraulic components and drive systems.

Electrical and Air Pressure Components

List of replacement parts for electrical and air pressure components.

Air and Oil Filter Components

List of replacement parts for air and oil filters.

Compressor Components

List of replacement parts for compressor components.

Chapter 8: Troubleshooting Guide

Limited Warranty Statement