WALL-MOUNT AIR HANDLERS
2-3TON COOLING/HEAT PUMP
18-GF06D1-1
TMM5A0B24M21SAA
TMM5A0B30M21SAA
TMM5A0B36M31SAA
ALL phases of this installation must comply with NATIONAL, STATE AND LOCAL CODES
Important: This Document is customer property and is to remain with this unit.
Installer’s Guide
Section 1. Features
1.1 Standard Features
噝 FRONT OR BOTTOM RETURN AIR.
噝 PAINTED FINISH ON GALVANIZED STEEL
噝 STURDY POLYCARBONATE DRAIN PANS
- The TMM5A wall mount air handler has factory
installed drain pans and is shipped for upflow
applications only.
噝
208/230 VAC OPERATION
噝
MULTI-SPEED DIRECT DRIVE BLOWER
CONSTANT TORQUE ECM MOTOR WITH
FAN-OFF TIME DELAY PROGRAMMING
噝 FACTORY INSTALLED R-410A THERMAL
EXPANSION VALVE
1.2 Optional Accessories
噝 5, 7.5 and 10 kW SINGLE PHASE ELECTRIC
HEATERS
- Circuit breakers are standard on all single
phase 5,
7.5 and 10 kW heaters.
The TMM5A series wall mount air handler is designed for installation in a closet, utility room, alcove
and can be wall mounted. These versatile units are applicable to air conditioning and heat pump
applications. Field installed electric resistance heaters are available.
噝
STUD OR WALL MOUNTING TABS
噝
FULLY INSULATED CABINET
噝
3/4'' NPT PRIMARY AND SECONDARY DRAINS
7)0575$16)250(5
)/)86(/,1.
)0)$102725
&$3 )$1 &$3$&,725
*1' *5281'
),(/' 32:(5 :,5,1*
*1'
9ᨺ
&20
9
9
7)05
FM
%51&
%/8
<**1'
:+,7(
<(/1
%/./
NOTES:
1: Use Copper Wire (75 Min) Only Between Disconnect Swicth And Unit .
2: To Be Wired In Accordance With NEC And Local Codes.
3: If Any Of The Original Wire ,As Supplied,Must Be Replaced.Use The Same
Or Equivalent Type Wire.
4: Connect R To R,G To G,Etc.See Outdoor Instruction For Details.
5: To Change Speed Tap,Move Blue Wire Desird Terminal.
6: See Airflow Tables For Tap Usage.
7:Factory Wires May Be Present,DO NOT USE.
ć
7)0575$16)250(5
)/)86(/,1.
)0)$102725
&$3 )$1 &$3$&,725
*1' *5281'
),(/' 32:(5 :,5,1*
*1'
9ᨺ
&20
9
9
7)05
FM
%51&
%/8
<**1'
:+,7(
<(/1
%/./
NOTES:
1: Use Copper Wire (75 Min) Only Between Disconnect Swicth And Unit .
2: To Be Wired In Accordance With NEC And Local Codes.
3: If Any Of The Original Wire ,As Supplied,Must Be Replaced.Use The Same
Or Equivalent Type Wire.
4: Connect R To R,G To G,Etc.See Outdoor Instruction For Details.
5: To Change Speed Tap,Move Blue Wire Desird Terminal.
6: See Airflow Tables For Tap Usage.
7:Factory Wires May Be Present,DO NOT USE.
ć
7)0575$16)250(5
)/)86(/,1.
)0)$102725
*1'
&20
9
9
7)05
NOTES:
1: Use Copper Wire (75 Min) Only Between Disconnect Swicth And Unit .
2: To Be Wired In Accordance With NEC And Local Codes.
3: If Any Of The Original Wire ,As Supplied,Must Be Replaced.Use The Same
Or Equivalent Type Wire.
4: Connect R To R,G To G,Etc.See Outdoor Instruction For Details.
5: To Change Speed Tap,Move Green Wire Desird Terminal.
6: See Airflow Tables For Tap Usage.
ć
FM
<**1'
1
&
/
To Next Page
Need help?
General
