Why is the detector's siren sounding on my AMERITECH Security System?
If the detector's siren is sounding on your AMERITECH Security System, it could be due to the unit not receiving the required power. Check for proper installation of the battery and try a new battery. Alternatively, the unit may be malfunctioning, and you should replace the detector.
Why is the digital communicator message not being received from my AMERITECH SecurityLink AM100?
If the digital communicator message is not being received from your AMERITECH Security System, it could be due to the following reasons: * The AM100 is in TEST mode. Remove it from TEST mode. * The telephone connection is not secure. Check all connections. * The digital communicator is malfunctioning. Check with a different AM100. * The telephone number in the program needs a prefix or access code. Program the prefix or access code into the AM100. * The telephone call to the central monitoring station requires operator assistance. The AM100 system cannot work in this situation.
With 5800 System, what to do if there is no response to a transmitter in normal operation, although zone number clears during Transmitter Sniffer mode on AMERITECH SecurityLink AM100?
If, with a 5800 System, there is no response to a transmitter in normal operation, but the zone number clears during Transmitter Sniffer mode on your AMERITECH Security System: * If another input causes the zone to be displayed, the wrong input was 'enrolled' during programming. Delete the input's serial number (not the zone) and enroll the proper input (see field *56). * If there is no response at all from this transmitter, this physical transmitter has not been enrolled by the system. Determine which transmitter is programmed for this zone and reprogram as necessary.
What to do if my AMERITECH SecurityLink AM100 Security System transmitter signal is not received?
If the transmitter signal is not being received by the 5881/5882 unit of your AMERITECH Security System, consider these potential causes and solutions: * The transmitter or 5881/5882 might not be properly powered. Check or change the transmitter's battery and check the AM100's AC power. * If the transmitter is a 5827/5827BD, the house code might not be set correctly. Check the code switches inside the transmitter to ensure they match the RF House Code programmed in the AM100. * The transmitter may be located too far from the RF receiver. Try moving the transmitter or RF receiver closer. * Metal shielding might be interfering with the signal. Check for large metal obstructions and relocate the transmitter if necessary. * The transmitter might be malfunctioning. Verify by activati...
Guidance on optimal placement of smoke/heat detectors for effective fire detection.
Recommendations for positioning intrusion sensors at entry points for coverage.
Explains symbols, icons, and formatting used in the manual.
Details characteristics of the 8 basic hardwired zones, including supervision and response.
Covers wired and wireless expansion zones, detailing supported modules and zone counts.
Lists compatible keypad models and their features for system interaction.
Details installer, master, babysitter, and duress codes for system access.
Covers zone monitoring, output relays, phone module, and paging capabilities.
Details long range radio, line monitoring, programming, and power supply.
Specifies the minimum required backup battery size and type.
Instructions for securely mounting the control cabinet and installing the lock.
Steps for mounting the main circuit board and RF receiver.
Details wiring for standard telephone line connections.
Guides for wiring 1321 and 4300 transformers.
Steps for connecting the backup battery and earth ground.
Lists compatible keypads and provides wiring charts and guidance.
Instructions for mounting keypads and using extra power supplies.
Steps to verify system readiness before full wiring.
Details zone features like EOLR supervision and wiring for burglary devices.
Specific instructions for wiring 2-wire smoke and 4-wire smoke/combustion detectors.
Instructions for connecting 2-wire latching glass break detectors on zone 8.
Steps for programming zones and verifying their operation.
Information on adding expansion modules like 4219 and 4229.
Steps to test wired expansion zones after installation.
General info on wireless zones, receiver supervision, and house ID.
Detailed steps for installing and configuring the RF receiver.
Installing the 5800TM module and general transmitter information.
Details transmitter types, battery expectations, and the sniffer mode test.
A table listing transmitter models, input types, and special notes.
Performing Go/No Go tests and setting DIP switches for 5827 transmitters.
Explains relay/PLC functions, programming, and setup for 4204/4229 modules.
Details Powerline Carrier device functionality and the need for a 4300 transformer.
Wiring the 4300 transformer and programming relay actions.
Overview of phone module capabilities and instructions for mounting.
Details phone module wiring and connecting Caller ID units.
Important wiring notes and diagrams for the phone module.
Steps for programming and testing the phone module's functionality.
Lists compatible sounders and important UL installation notes.
Instructions for connecting sounders and performing tests.
Explains long range radio use and details its wiring.
Steps for installing and wiring the remote keyswitch.
Wiring diagrams for keyswitch installation with/without 4300 transformer.
Instructions for programming zone 7 for keyswitch operation.
Explains how to use the keyswitch and interpret LED status.
Explains AAV for voice dialog and provides wiring guidance.
Diagrams for connecting AAV with and without a phone module.
Steps for final power-up, including grounding, AC connection, and battery calculation.
Instructions for connecting the battery and a worksheet for current draw.
Overview of programming modes, data storage, and entering data fields.
Details interactive modes (✱56, ✱80, etc.), loading defaults, and exiting programming.
Explains zone types and lists definitions for various types (00-24).
Fields ✱20 (Installer Code), ✱22 (RF System), ✱24 (RF House ID).
Fields ✱25 (Wired Zone Expansion), ✱26 (Chime by Zone).
Fields ✱27 (Powerline Carrier ID), ✱29 (LRR Output), ✱30 (Keyswitch), ✱32 (Fire Sounder Timeout).
Fields ✱28 (Phone Module Code), ✱31 (Single Alarm Sounding).
Fields ✱33-✱36 for alarm timing and entry/exit delays.
Fields ✱37-✱39 for arming warnings, dings, and power-up state.
Fields ✱40-✱44 for PABX, phone numbers, and account numbers.
Fields ✱47 (Phone System Select), ✱48 (Report Format).
Description for field ✱49 regarding split/dual reporting.
Fields ✱50 (Dialer Delay), ✱51 (Periodic Test), ✱52 (Test Offset), ✱53 (SESCOA/RADIONICS).
Fields ✱59-✱67 for various system status and report codes.
Fields ✱68-✱76 and ✱88, ✱89 for restore codes and pager setup.
Fields ✱90 (Event Logging), ✱91 (Option Selection), ✱92 (Phone Line Monitor), ✱93 (Number of Reports).
Fields ✱94, ✱95 and programming commands ✱56, ✱80, etc.
Introduction to zone programming and using transmitters as tools.
Assigning zone types, report codes, and input device types.
Procedures for entering loop numbers and learning transmitter serial numbers.
Confirming enrollment and prompting for alpha descriptors.
Defines ACTION and START programming for output devices.
Explains STOP programming options for de-activating devices.
Steps for programming devices and lists of zone/system operation choices.
A practical example demonstrating output device programming.
Instructions for creating, deleting, and managing zone lists.
Explains programming user-friendly zone descriptions.
How programmed zone descriptors are displayed.
Steps for saving descriptors and exiting the programming mode.
Procedure for adding custom words for zone descriptors.
Reference lists for words and characters used in descriptors.
Steps for sequentially enrolling wireless transmitters.
Procedures for learning and confirming transmitter serial numbers.
Completing the enrollment process and exiting the mode.
Information on remote programming capabilities and required equipment.
Details on remote functions and important advisory notes.
Explains communication formats and the handshake/kissoff process.
In-depth explanations of various report format structures.
A list of Contact ID event codes and their meanings.
Explains installer, master, and secondary user codes.
Details keypad operations, arming modes, and system commands.
Summarizes arming modes and explains exit error alarm displays.
Explains common trouble messages and other system status displays.
Step-by-step instructions for testing the entire security system.
Testing wireless transmitters and installer responsibilities.
A table addressing common wireless system symptoms and causes.
A table addressing control and smoke detector problems.
Steps to take before contacting technical support for assistance.
FCC statements regarding radio frequency energy and telephone connections.
Technical specifications for the main control unit and keypad.
Technical specifications for various system components.
Lists compatible accessories and specifications for smoke/combustion detectors.
Identifies input loops for 5800 series wireless transmitters.
Details potential failure points and limitations of the alarm system.
Outlines the seller's obligations and limitations for product warranty.
General| Type | Wireless Security System |
|---|---|
| Battery Backup | Yes |
| Communication | Cellular |
| Wireless Frequency | 319.5 MHz |
| Power Supply | AC Adapter |
| Zones | 8 |
To Next Page
