What causes Under Voltage Fault in Amtech Axpert-Eazy AMT-200-4 DC Drives?
An Under Voltage Fault in Amtech DC Drives can be caused by the DC Bus voltage falling below the under voltage level. Check the input power supply and correct it if necessary. Also check soft charge contactor or connection.
What to do if Amtech Axpert-Eazy AMT-200-4 DC Drives have Thermistor Over Temperature Fault?
If your Amtech DC Drive is showing a Thermistor Over Temperature Fault, it could be due to several reasons. A trouble may have occurred in the cooling blower, so replace it if necessary. The ambient temperature may have risen, so lower the ambient temperature (less than 50 °C for 400 V series or less than 40 °C for 500 V / 600 V series). The temperature switch (thermostat) or thermistor may not be connected or loosely connected at J16 and J13 respectively, so disconnect thermostat switch connection at J16 and ensure that the thermostat shows short circuit. Disconnect the thermistor and ensure that the thermistor shows resistance greater than 2.2 kΩ but less than 60 kΩ. Reconnect thermostat and thermistor properly.
How to fix U Phase Current Sensor Fail Fault on Amtech DC Drives?
To address a U Phase Current Sensor Fail Fault on Amtech DC Drives, first, check for a loose connection of the hall current sensor cable connected at J12 of PCA-2014A. Switch off the unit, remove the cable, and inspect both sides for proper crimping. If you find any issues, replace the cable and check again. Second, one or more current sensors may have failed. Remove connector J12 and reset the fault. If the fault can be reset, identify the failed current sensor. If, after removing connector J12, the problem persists, replace PCA-2014A.
What causes an Adjustable Over Current Fault in Amtech Axpert-Eazy AMT-200-4 DC Drives?
An Adjustable Over Current Fault in Amtech DC Drives can be triggered by a few factors. The motor current data might be set incorrectly, so set correct motor current data in B103. Alternatively, the adjustable over current settings may be too low, so increase the adjustable over current level (B302). Finally, the output current might be too high, so reduce the motor load.
What to do if Amtech Axpert-Eazy AMT-200-4 DC Drives display a Communication Loss?
If an Amtech DC Drive displays a Communication Loss, it could be due to several reasons. There may be a problem in display board PCA-2012, so replace the display board PCA-2012 and check again. Also, there may be a problem in control board PCA-2014A. If +5 V supply or +3.3 V supply is not coming then also this fault will come. Check the power supply unit and if problem is found replace it, or replace the DSP control board PCA-2014A and check again. You can also disable the fault using C405. This will allow the inverter to run in case of communication loss between the PCA-2014A DSP control board and PCA-2012 LCD display board.
Why does my Amtech DC Drive show a Drive Over Load Fault?
An Amtech DC Drive may show a Drive Over Load Fault because the AC drive is overloaded. Ensure that motor current data are properly set in B103. Reduce the load or increase the motor and AC DRIVE capacity. If this occurs at low speed, reduce the torque boost settings (A501 / A502) or DC braking settings (A307 / A308).
What to do if my Amtech DC Drives show a Ground Fault?
If your Amtech DC Drive indicates a Ground Fault, it may be due to a short in the output line or motor. Check that no output is shorted to ground; partially damaged output cables can also cause this. Another possibility is a problem with one or more current sensors. Remove the current sensor feedback and check. If the fault persists, replace PCA-2014A, otherwise replace the problematic current sensor.
Essential safety guidelines to prevent hazards and ensure correct usage.
Guidance on receiving, inspecting, and storing the AC drive unit safely.
Recommendations for selecting a suitable installation location and ventilation.
Critical safety warnings and procedures for connecting power supply and motor.
Guidelines for wiring control circuits to prevent interference and ensure safety.
Step-by-step guide on navigating and changing parameter values.
Essential checks and preparations before energizing the drive.
Procedure for entering motor rating parameters for proper operation.
Guide to performing automatic tuning for optimal motor performance.
Comprehensive list and explanation of parameters for Mode-A.
Comprehensive list and explanation of parameters for Mode-B.
Comprehensive list and explanation of parameters for Mode-C.
Scheduled inspections and checks required for the AC DRIVE.
Configuration details for connecting host computer and Axpert-Eazy units via RS485.
Technical details of the serial communication interface and protocol.
Overview of the Modbus protocol, transactions, and transmission modes.
Key points to observe when using the inverter as a UL/cUL compatible product.
Guidelines for installation environments to meet EMC directives.
Precautions and connection details for input filters to manage electrical shock hazards.
Recommendations for wiring and earthing to reduce EMI and ensure immunity.
To Next Page
General