Anton Paar DMA 4100 M User Manual (English)

Other manuals for Anton Paar DMA 4100 M

Questions and Answers:

S
Sarah ReillySep 15, 2025
Why is there no printout on my office printer from Anton Paar Measuring Instruments?
- A
  Audrey BerrySep 16, 2025
  If you're experiencing no printouts on your office printer from Anton Paar Measuring Instruments, it could be due to several office printer problems. Check if the printer has enough paper, toner, etc. See the respective printer instruction manual. Also, the office printer type may not be supported by your instrument, or the wrong interface might be used. Use the interface defined in the "Printer Management" menu or change the interface settings. Additionally, verify the printer definition in the "Printer Management" menu and change the definition if necessary.
R
Ryan MartinezAug 25, 2025
What to do if my Anton Paar DMA 4100 M Measuring Instruments calibration failed and results deviate from reference values?
- K
  Kara JohnsonAug 25, 2025
  If the calibration of your Anton Paar Measuring Instruments fails and the results deviate from reference values, consider the following possible causes: inadequate cleaning and drying procedures, use of calibration liquid that has been stored for too long, or adjustment problems. You should improve your cleaning and drying procedure, use a fresh calibration liquid, and improve your adjustment routine.
E
Erica DelgadoAug 25, 2025
What to do if my Anton Paar Measuring Instruments calibration failed?
- M
  Melinda HayesAug 26, 2025
  If the calibration of your Anton Paar Measuring Instruments fails and the results deviate from reference values, consider the following possible causes and solutions: 1. Inadequate cleaning and drying: Improve your cleaning and drying procedure. 2. Expired calibration liquid: Use a fresh calibration liquid. 3. Adjustment issues: Improve your adjustment routine.
T
Thomas HunterAug 26, 2025
What does 'Filling Warning' mean on my Anton Paar DMA 4100 M?
- T
  Teresa HillAug 27, 2025
  A 'Filling Warning' on your Anton Paar Measuring Instruments indicates that there are gas bubbles in the measuring cell. To resolve this, degas your sample and fill the sample at a higher temperature than the measuring temperature.
P
Patrick CardenasAug 27, 2025
How to fix wrong output data exported from Anton Paar Measuring Instruments?
- M
  Monica LeeAug 27, 2025
  If your Anton Paar Measuring Instruments exports wrong output data, the settings in the "Result Output" menu are likely incorrect. To fix this, change the settings in that menu.
W
William MurilloSep 12, 2025
How to fix a failed adjustment of Anton Paar Measuring Instruments after 10 minutes?
- H
  Heather HughesSep 12, 2025
  If the adjustment of your Anton Paar Measuring Instruments is not finished after 10 minutes, it may be because: * The measuring cell is not sufficiently dry for the air adjustment. Clean and dry the measuring cell perfectly before an air check/adjustment. * There are gas bubbles in the measuring cell during water adjustment. Repeat the filling procedure and use freshly degassed ultra-pure (bi-distilled or deionized) water.
K
Kelly BoydSep 9, 2025
What to do if Anton Paar Measuring Instruments shows Density Condition: "Error: No Oscillation"?
- R
  Rebecca StevensSep 10, 2025
  If your Anton Paar Measuring Instruments displays the error message "Error: No Oscillation", it means the measuring cell is only partly filled. Fill the sample again.
S
Sonia RyanSep 12, 2025
What to do if Anton Paar Measuring Instruments displays Density Condition: "Timeout Error"?
- D
  Danielle SimpsonSep 12, 2025
  If your Anton Paar Measuring Instruments displays a "Timeout Error", it could be due to: * An unstable sample (e.g., emulsion). Prethermostat your sample. * A timeout setting that is too short. Change the timeout setting.
S
Shelly KirbySep 3, 2025
What to do if Anton Paar DMA 4100 M boots up without logon procedure?
- J
  John PooleSep 3, 2025
  If your Anton Paar Measuring Instruments boots up without a logon procedure and no password is requested, it's because a user with the auto logon function activated was logged on before the instrument was switched off. To resolve this, tap on the user indicator icon and log on with another user account.
R
Robert McdanielSep 1, 2025
What to do if I do not hit the screen elements on Anton Paar Measuring Instruments?
- B
  bnavarroSep 1, 2025
  If you are unable to accurately touch screen elements on your Anton Paar Measuring Instruments, it is likely due to bad touch screen calibration. Perform a new touch screen calibration to resolve this issue.

Anton Paar DMA 4100 M Specifications

General

Measurement Principle	Oscillating U-tube
Viscosity Correction	Yes
Measuring Range (Density)	0 to 3 g/cm³
Accuracy (Density)	0.0001 g/cm³
Repeatability (Density)	±0.00005 g/cm³
Temperature Accuracy	0.03 °C
Temperature Repeatability	±0.01 °C
Sample Volume	1 mL
Display	Color display
Connectivity	USB, Ethernet
Data Storage	1000 results
Power Supply	100-240 V