CONTENT
A. GENERAL ................................................................................................................................................................................................................................................................................... 6
A.1 INTRODUCTION .................................................................................................................................................................................................................................................................................. 6
A.2 APPLICATIONS ................................................................................................................................................................................................................................................................................... 6
A.3 MAIN CHARACTERISTICS................................................................................................................................................................................................................................................................... 7
A.4 SAFETY PROVISIONS.......................................................................................................................................................................................................................................................................... 7
Compliance with Safety Standards ............................................................................................................................................................................................................................................. 7A.4.1
Following Instructions supplied with the accompanying Documents .......................................................................................................................................................................................... 7A.4.2
Taking Measurements ................................................................................................................................................................................................................................................................ 7A.4.3
Instructions to be followed before Use........................................................................................................................................................................................................................................ 7A.4.4
Faults and abnormal Constraints ............................................................................................................................................................................................................................................... 8A.4.5
Table of Symbols used ................................................................................................................................................................................................................................................................ 8A.4.6
Maintenance .............................................................................................................................................................................................................................................................................. 8A.4.7
B. DESCRIPTION ............................................................................................................................................................................................................................................................................ 9
B.1 General View .......................................................................................................................................................................................................................................................... 9
B.2 DISPLAY .......................................................................................................................................................................................................................................................................................... 10
B.3 ACCESSORIES .................................................................................................................................................................................................................................................................................. 11
Delivered with the Unit ............................................................................................................................................................................................................................................................ 11B.3.1
Options delivered to order ....................................................................................................................................................................................................................................................... 11B.3.2
C. OPERATION ............................................................................................................................................................................................................................................................................. 12
C.1 REMINDERS OF THE 4-WIRE PRINCIPLE ............................................................................................................................................................................................................................................ 12
C.2 PERFORMING A MEASUREMENT ...................................................................................................................................................................................................................................................... 12
Switching On ......................................................................................................................................................................................................................................................................... 14C.2.1
Selecting the Range ............................................................................................................................................................................................................................................................... 14C.2.2
Selecting the Measurement Mode ............................................................................................................................................................................................................................................. 14C.2.3
Ambient temperature compensation ...................................................................................................................................................................................................................................... 18C.2.4
Setting Alarms ....................................................................................................................................................................................................................................................................... 19C.2.5
Connecting to Connectors ........................................................................................................................................................................................................................................................ 19C.2.6
Standby (STBY) Position ........................................................................................................................................................................................................................................................ 20C.2.7
C.3 LIST OF ERROR MESSAGES .............................................................................................................................................................................................................................................................. 21
C.4 CONFIGURING THE UNIT ............................................................................................................................................................................................................................................................... 22
Principle .................................................................................................................................................................................................................................................................................. 22C.4.1
Direct Access Key .................................................................................................................................................................................................................................................................... 22C.4.2
Entering a Number .................................................................................................................................................................................................................................................................. 22C.4.3
Programming Menu Table ....................................................................................................................................................................................................................................................... 23C.4.4
Managing an Alarm Threshold: ALAr ...................................................................................................................................................................................................................................... 24C.4.5
Using the DB9 Connector: rS .................................................................................................................................................................................................................................................. 24C.4.6
Managing and printing Memory Content: mEm ....................................................................................................................................................................................................................... 24C.4.7
Programming the temperature compensated measurement Value ....................................................................................................................................................................................... 28A.1.1
 CONFIGURATION AND OPERATION COMMANDS USING THE RS232 SERIAL LINK .................................................................................................................................................. 29
C.5 INTRODUCTION ................................................................................................................................................................................................................................................................................ 29
Command Errors ............................................................................................................................................................................................................................................................... 30A.1.2
C.6 LIST OF COMMANDS ........................................................................................................................................................................................................................................................................ 31
C.7 GENERAL COMMANDS ..................................................................................................................................................................................................................................................................... 32
C.8 PROGRAMMING COMMANDS ........................................................................................................................................................................................................................................................... 33
C.9 MEMORY USAGE COMMANDS ......................................................................................................................................................................................................................................................... 36
C.10 OTHER INFORMATION COMMANDS ................................................................................................................................................................................................................................................ 38
C.11 LOGOM PROGRAM ....................................................................................................................................................................................................................................................................... 38
Installation ........................................................................................................................................................................................................................................................................ 38A.1.3
Use .................................................................................................................................................................................................................................................................................... 38A.1.4
D. MAINTENANCE ....................................................................................................................................................................................................................................................................... 40
D.1 OPENING/CLOSING THE UNIT .......................................................................................................................................................................................................................................................... 40
D.2 BATTERY PACK ............................................................................................................................................................................................................................................................................... 42
Charging ................................................................................................................................................................................................................................................................................. 42D.2.1
Replacing the Battery .............................................................................................................................................................................................................................................................. 42D.2.2
D.3 FUSES .............................................................................................................................................................................................................................................................................................. 42
D.4 CHECKING PERFORMANCE .............................................................................................................................................................................................................................................................. 43
D.5 MANAGING MAINTENANCE ............................................................................................................................................................................................................................................................. 43
D.6 UPDATING THE ON-BOARD SOFTWARE ........................................................................................................................................................................................................................................... 44
D.7 ADJUSTMENT ................................................................................................................................................................................................................................................................................... 45
Environment ............................................................................................................................................................................................................................................................................ 45D.7.1
Adjusting the Unit .................................................................................................................................................................................................................................................................... 45D.7.2
D.8 WARRANTY ..................................................................................................................................................................................................................................................................................... 46
E. SPECIFICATIONS .................................................................................................................................................................................................................................................................... 47
E.1 APPLICABLE STANDARDS ................................................................................................................................................................................................................................................................ 47
Safety Class ............................................................................................................................................................................................................................................................................. 47E.1.1
EMC Conformity ...................................................................................................................................................................................................................................................................... 47E.1.2
Ambient Conditions .................................................................................................................................................................................................................................................................. 47E.1.3
Mechanical Conditions ............................................................................................................................................................................................................................................................ 47E.1.4
Measurement under Reference Conditions ............................................................................................................................................................................................................................... 47E.1.5
E.2 CHARACTERISTICS ........................................................................................................................................................................................................................................................................... 48
General .................................................................................................................................................................................................................................................................................... 48E.2.1
Resistance measuring function ................................................................................................................................................................................................................................................. 48E.2.2
Protections ............................................................................................................................................................................................................................................................................... 48E.2.3
E.3 END OF UNIT SERVICE LIFE ............................................................................................................................................................................................................................................................. 49
Waste Generated by the Unit .................................................................................................................................................................................................................................................... 49E.3.1
Unit Destruction Procedure ..................................................................................................................................................................................................................................................... 49E.3.2
F. ANNEXES .................................................................................................................................................................................................................................................................................. 50
F.1 UNIT MAINTENANCE PROGRAMMING DIAGRAM .............................................................................................................................................................................................................................. 51
F.2 DIAGRAMME DE PROGRAMMATION ET DE LECTURE DE L'APPAREIL ................................................................................................................................................................................................. 52
To Next Page
Loading...
