Why is my Aprilaire 8400 display blank?
If your Aprilaire Thermostat display is blank, there might be a few reasons: * Check the circuit breaker and reset it if necessary. * Ensure the power switch at the heating & cooling system is turned on. * Confirm that the furnace door is closed securely. * If your thermostat is battery powered, make sure that fresh AA alkaline batteries are correctly installed.
What to do if my Aprilaire Thermostat cooling system does not respond?
If your Aprilaire Thermostat's cooling system isn't responding when "COOLING" appears on the screen, consider the following: * Check for 24 VAC at the equipment on the secondary side of the transformer between power and common. If voltage is not present, check the cooling equipment to find the cause of the problem. * Check for 24 VAC between the cooling terminal (Y) and the transformer common. If 24 VAC is present, the thermostat is functional. Check the cooling system to find the cause of the problem. * Inspect for loose or broken wires between the thermostat and the cooling equipment. * Verify that SW1 (Equipment Type) is correctly set to match the installed heating/cooling equipment. * Ensure that heating and cooling wires are not shorted together.
What to do if my Aprilaire 8400 heating system does not respond?
If your Aprilaire Thermostat's heating system isn't responding when "HEATING" appears on the screen, here are a few things to check: * Make sure the heating and cooling temperatures are set to acceptable ranges: Heat: 45° to 90°F (7° to 32°C). Cool: 50° to 99°F (10° to 37°C). * Check for 24 VAC at the equipment on the secondary side of the transformer between power and common. If voltage is not present, check the heating equipment to find the cause of the problem. * Check for 24 VAC between the heat terminal (W) and the transformer common. If 24 VAC is present, the thermostat is functional. Check the heating equipment to find the cause of the problem. * Look for loose or broken wires between the thermostat and the heating equipment.
What to do if the Aprilaire Thermostat heating system does not respond?
If your Aprilaire thermostat's heating system isn't responding ('HEATING' appears on the screen), try these steps: First, check the circuit breaker and reset it if needed. Next, ensure the power switch at your heating and cooling system is turned on. Also, make sure the furnace door is securely closed. If your thermostat uses batteries, ensure fresh AA alkaline batteries are correctly installed. Finally, verify that your heating temperature is set between 45° to 90°F (7° to 32°C).
Why is my Aprilaire 8400 cooling system not responding?
If your Aprilaire thermostat's cooling system isn't responding ('COOLING' appears on the screen), consider the following: Check for 24 VAC at the equipment on the secondary side of the transformer between power and common. If voltage is absent, inspect the cooling equipment to identify the problem. Verify there's 24 VAC between the cooling terminal (Y) and the transformer common. If present, the thermostat is likely functional, so check the cooling system. Inspect for loose or broken wires between the thermostat and the cooling equipment. Ensure SW1 (Equipment Type) is correctly set to match your installed heating/cooling equipment. Lastly, confirm that heating and cooling wires are not shorted together.
How to fix Aprilaire Thermostat when heating system does not respond?
If your heating system isn't responding to your Aprilaire Thermostat, try these steps: * Check for 24 VAC at the equipment on the secondary side of the transformer between power and common. * See if there's 24 VAC between the heat terminal (W) and the transformer common. * Look for any loose or broken wires between the thermostat and the heating equipment.
Why is my Aprilaire Thermostat fan not turning on when heating?
If the fan on your Aprilaire Thermostat isn't turning on when the system is calling for heat, here are a couple of things you can check: * Verify System Setting #02 (Fan Control) to ensure the fan control is properly set to match the type of system. * Change the System Mode to Heat, and set the temperature level above the current room temperature.
Why is my Aprilaire Thermostat heat pump blowing cool air in heat mode or warm air in cool mode?
If your heat pump is blowing cool air in heat mode or warm air in cool mode, here's what you should check on your Aprilaire Thermostat: * Check System Setting #12 (Reversing Valve) to make sure it is properly configured for your system. * Change the System Mode to Cool, and set the temperature level below the current room temperature.
What to do if my Aprilaire 8400 display is blank?
If your Aprilaire Thermostat display is blank, here are a few things you can check: * First, check the circuit breaker and reset it if necessary. * Make sure the power switch at the heating & cooling system is on. * Also, ensure the furnace door is closed securely. * If your thermostat is battery powered, make sure fresh AA alkaline batteries are correctly installed.
What to do if Aprilaire Thermostat heating equipment is running in cool mode?
If your heating equipment is running in cool mode on your Aprilaire Thermostat, you can try the following: Check System Setting #02 (Fan Control) to ensure the fan control is correctly set to match your system type. Also, change the System Mode to Heat and set the temperature higher than the current room temperature.
General| Thermostat Type | Digital |
|---|---|
| Programmability | 7-day programmable |
| Humidification Control | Yes |
| Dehumidification Control | Yes |
| Ventilation Control | Yes |
| Air Filtration Control | Yes |
| Humidity Control | Yes |
| Temperature Control | Yes |
| Indoor Humidity Display | Yes |
| Outdoor Temperature Display | Yes (with optional sensor) |
| Type | Programmable |
| Display | Touchscreen |
| Power Source | 24 VAC |
| Stages | 2 Heat / 2 Cool |
| Power Method | Hardwired |
| Connectivity | Wi-Fi (optional) |
| Warranty | 5 years |
To Next Page
