Arbortech AS170 - User Manual

Questions and Answers

J
Jason CrosbyAug 21, 2025
How to fix Arbortech Saw motor overheating?
- R
  Roger LawsonAug 21, 2025
  To prevent your Arbortech Saw motor from overheating, make sure all cooling vents are free from obstructions. Ensure the blades aren't rubbing with excessive force. Replace worn blades. Check that the belt tension isn't too high. Inspect the bearings for any roughness by removing the plastic side cover and belt, then rotate both pulleys. Also, confirm that the motor housing is securely attached to the tool. If it's loose, seek assistance from an authorized service center.
C
carolperkinsSep 4, 2025
How to fix loose top handle on Arbortech AS170?
- M
  matthew83Sep 4, 2025
  If you have a loose top handle on your Arbortech Saw, worn or damaged rubber bushes could be the cause. Replace them to resolve this issue.
R
Raven RobertsonSep 2, 2025
Why Arbortech AS170 blades continually coming loose?
- D
  Daniel PowellSep 3, 2025
  If the blades on your Arbortech Saw are continually coming loose, inspect the blade bolt holes. If the bolt holes are elongated, replace the blades.
A
Amy CooperSep 1, 2025
What to do if Arbortech AS170 Saw blades rubbing together with excessive force?
- K
  Katrina EllisonSep 1, 2025
  If the blades of your Arbortech Saw are rubbing together with excessive force, remove the blade/s and bend slightly to correct.
A
Anthony MyersAug 30, 2025
Why Arbortech AS170 blades rubbing against each other with excessive force?
- D
  David AlexanderAug 31, 2025
  If the blades of your Arbortech Saw are rubbing against each other with excessive force, you might be trying to cut material that is too hard.
C
Connie RothAug 29, 2025
What to do if Arbortech AS170 blade mounting bolts not tightening fully?
- C
  Connor HensonAug 29, 2025
  If the blade mounting bolts on your Arbortech Saw aren't tightening fully, the threads on the bolts may be stripped. Replace the bolts.
C
cunninghamrodneyAug 27, 2025
Why is Arbortech AS170 cutting performance slow?
- J
  Joanne HicksAug 27, 2025
  If you're experiencing slow cutting performance with your Arbortech Saw, the teeth may be worn, chipped, or missing. Try sharpening or replacing the blade. Also, check for a slipping belt.
R
Rebecca KnoxAug 26, 2025
How to troubleshoot noisy operation or unusual vibration in Arbortech AS170 Saw?
- C
  Chad SanchezAug 27, 2025
  If your Arbortech Saw exhibits noisy operation or unusual vibration, check if the blades are loose and tighten the blade mount bolts. If that's not the case, the blade may have failed and needs replacement. For leaf spring failure, bearing failure, or gearbox failure, contact an authorized service center. If the handle rubber mounts are damaged or worn, replace them.
V
vandersonAug 25, 2025
Why are Arbortech AS170 Saw blades “blueing”?
- W
  William FullerAug 25, 2025
  If your Arbortech Saw blades are 'blueing', this could be due to worn teeth, excessive force, insufficient sawing motion, or attempting to cut material that is too hard. It could also be caused by blades rubbing together with excessive force. Replace worn blades and reduce the force applied during cutting.
C
Casey SmithAug 23, 2025
What to do if Arbortech AS170 Saw is running but blades not moving?
- R
  rrobbinsAug 23, 2025
  If your Arbortech Saw is running, but the blades aren't moving, the belt may be loose, broken, or worn. Try re-tensioning or replacing the belt as needed.