EN
EN-23
Locking/Unlocking a specific
Device Mode
When you first unpack your remote and insert the
batteries, it is able to control certain Arcam components
automatically (e.g. BD players, Amplifiers, Tuners and
CD Players). We achieve this by programming specific
Arcam device codes onto the relevant Device Mode
keys, then locking the Device Modes so you don’t
reprogram them inadvertently.
If you want to override these locked default settings
– to control a third-party BD player, for example – you
will first need to unlock BD Mode before setting up the
remote using one of the learning methods described
on the previous page.
Here are the factory default settings:
Device
Mode
Default
status
Default codes
AMP Locked 001 (Arcam code 16)
BD Locked 001 (Arcam)
AV Unlocked 108 (Philips TV)
PC USB Unlocked Code learning only
GAME Unlocked Code learning only
STB Unlocked 030 (Bush/Goodmans/
Grundig, from SAT
database)
SAT Unlocked 128 (Sky+ Digital, from
SAT database)
PVR Unlocked 018 (Humax PVR, from
SAT database)
CD Locked 001 (Arcam)
Alternative codes are available for multi-room solutions,
or in the case of code clashes with other manufacturer’s
products.
For example:
(system code 19): 002
Note that you need to change the system code on the
product you wish to control, as well as the remote.
, and are the Device keys that may be
Locked or Unlocked. Lock and Unlock are toggles (they
change from Lock to Unlock to Lock, etc.).
1. Press and hold the Device and
keys together for
three seconds. The power LED stays lit, showing that
it is in Lock/Unlock setup mode.
2. If there is no further key input for 30 seconds, the
LED goes off and the remote leaves Lock/Unlock
setup mode.
3. To toggle the status of a device and then verify the
status of a device, press the
keys in sequence:
If you have locked the device, the LED blinks three
times:
.
If unlocked the device, the LED blinks five times:
.
4. If you press a valid Device key within 30 seconds,
the LED blinks three times:
and the
remote leaves Lock/Unlock setup mode.
Controlling the volume of other
devices
By default, the volume keys and mute key control the
amplifier volume.
You can configure these buttons so they send volume
commands to another device. In the following example,
the volume commands are sent to a linked AV device
(your television, for instance):
Press
for three seconds, until the LED lights and
stays on.
Press
UP.
Press
again. The LED blinks three times
.
The volume and mute keys will now send the volume
commands to the TV.
To set the volume buttons to control the amplifier once
more, repeat the above steps, except press
in
step 3.
Hidden commands
Command Effect
AMP +
'
Sends a Power On command
AMP +
,
Sends a Power Off command
CD +
'
Sends a Power On command
CD +
,
Sends a Power Off command
BD +
'
Sends a Power On command
BD +
,
Sends a Power Off command
BD +
>
Sends a Resolution command
Factory default reset
You can reset your remote to the original factory default
settings.
Press and hold both the
(home) and keys for
about five seconds until the power LED blinks five times
.
All programming and setup codes that you have
entered into the remote are erased and the remote
returns to the original factory default settings.
Device codes
The tables at the end of this handbook list 3-figure
codes for different manufacturers’ devices.
Use these when setting your remote up to control your
devices, as described in “Direct code setup (Method 1)”
on page EN-22
If more than one code number is listed, try the first
number. If the results are unsatisfactory, continue trying
the numbers for that manufacturer to get the best ‘fit’
with the functionality required.
If the manufacturer of your equipment is not listed, you
can try “Library search setup (Method 2)” on page EN-22
This method allows you to scan through every code
contained in the remote’s memory.
To Next Page
Loading...
