Why is the water flow slow from the shower and filling spout in Arjo Bathtubs?
If the water flow from both the shower and filling spout of your Arjo Bathtubs is slow, check the incoming hot water line to see if it is hot. Also, inspect and clean the filter for the incoming water according to the Care and Preventive Maintenance section on page 52.
How to fix slow water flow to the shower in Arjo Bathtubs?
If the water flow to the shower in your Arjo Bathtubs is slow, inspect and clean the shower head. Refer to the Care and Preventive Maintenance section on page 52 for instructions.
What to do if there's water on the ground near my Arjo Bathtubs?
If you find water on the ground near your Arjo Bathtubs, immediately check for leaks in the incoming water lines and the bath drainage hose. Additionally, the bath may have short-circuited, causing it to fill continuously. In either case, turn off both the electrical and water supplies to the unit.
Why won't the auto fill function stop filling my Arjo Bathtubs?
If the auto-fill function on your Arjo Bathtubs doesn't stop, it might be due to residue buildup on the mechanical sensor plugs. Refer to the Cleaning and Disinfection Instructions on page 40 for guidance.
What to do if the fill or shower function stops on my Arjo Bathtubs?
If the fill or shower function on your Arjo Bathtubs stops working, reset the scalding protection. Follow the instructions for 'Reset scalding protection (P220 only) (5 steps) on page 18' or 'Reset scalding protection (P300 only) (4 steps) on page 19'.
What to do if disinfection does not work on Arjo Bathtubs?
If the disinfection process isn't working on your Arjo Bathtubs, ensure the bathtub is completely empty. Also, make sure that shower, fill or Hydromassage system, Hydrosound system are not activated. If the LED on the control panel is flashing and beeping P300 only, it means the disinfection level in the bottle is low and needs replacement. See section Cleaning and Disinfection Instructions on page 40!
Why is the sound not working on my Arjo Bathtubs Sound & Vision system, but the light is?
If the sound isn't working on your Arjo Bathtubs' Sound & Vision system, but the light is, the USB memory stick might be defective. If possible check the USB LED light for indication: Solid light power 21 Flashing light reading! Try using a different USB memory stick.
What to do if the Sound & Vision system hand control is not working on Arjo Bathtubs?
If the hand control for the Sound & Vision system in your Arjo Bathtubs isn't working, check if the LED on the remote control flashes when active. If it doesn't, replace the Sound & Vision system hand control.
Critical safety precautions to avoid injury, fire, shock, and falls.
Description and function of the P220 control panel buttons and display.
Description and function of the P300 control panel buttons and display.
How the scalding protection works and safety warnings.
Step-by-step guide to operating the Hydromassage system.
Step-by-step guide to operating the Hydrosound system.
Steps to change default settings for various bath functions.
Initial steps for preparing the bath with a lift hygiene chair.
Step-by-step instructions for transferring a patient using a lift hygiene chair.
Instructions for disinfecting the bath and hygiene chair after each use.
Initial steps for preparing the bath with a lift bath trolley.
How to check and adjust water temperature safely.
Steps for transferring a patient using a lift bath trolley.
The core step of bathing the patient.
Steps after bathing and preparing for showering.
How to use the shower handle and control water flow.
Safely checking water temperature and showering the patient.
How to check and adjust water temperature for patient comfort.
Instructions for disinfecting the bath and lift bath trolley after each use.
Safety warnings for disinfection to prevent cross-contamination and irritation.
Step-by-step guide to replacing the disinfectant bottle.
Steps to remove visible residue from the bath and accessories.
Detailed steps for cleaning the bath and accessories.
How to spray disinfectant on internal surfaces and the overflow outlet.
Steps for rinsing the bath and wiping contact areas.
How to disinfect drains and perform final rinsing and drying.
Steps to remove visible residue using a spray bottle.
Detailed steps for cleaning using a spray bottle.
How to spray disinfectant using a spray bottle on surfaces and overflow.
Steps for rinsing and wiping contact areas using a spray bottle.
How to disinfect drains and perform final rinsing and drying.
Schedule for caregiver obligations and maintenance checks.
Warning against modifying the equipment.
Requirements for annual servicing, calibration, and technician contact.
Warning that maintenance must be done by qualified personnel.
Troubleshooting steps for water flow and disinfection issues.
Troubleshooting for water leakage and electrical faults.
Explanation of error codes, their causes, and remarks for P300.
To Next Page
General