Need help?Do you have a question about the ARRI SkyPanel S30 and is the answer not in the manual?
General| Type | LED Softlight |
|---|---|
| Model | SkyPanel S30 |
| Tunable | Yes |
| Power Supply | 100-240 V AC, 50/60 Hz |
| Color Temperature Range | 2800K - 10000K |
| Control | DMX, Wireless |
| CRI | 95 |
| Beam Angle | 120° |
Physical dimensions for the SkyPanel S30 (manual and P.O. versions).
Physical dimensions for the SkyPanel S60 (manual and P.O. versions).
Physical dimensions for the SkyPanel S120-C (manual and P.O. versions).
Important safety instructions, notes, and explanation of warning signs.
Detailed safety guidelines and precautions for product operation.
Detailed safety guidelines and precautions for product operation.
Guidelines for product maintenance, light source replacement, and intended use.
Overview of SkyPanel features and product characteristics.
Steps for unpacking the product and its components.
Further details on the product's characteristics.
Further steps for unpacking the product.
Identifies key parts of the manual version fixture.
Identifies key parts of the P.O. version fixture.
Details the various connectors on the fixture's panel.
Describes the fixture's power supply units.
Instructions for mounting the stirrup and spigot.
Specific steps for mounting the spigot.
Procedure for attaching the fixture's stirrup.
Mounting safety brackets and dismantling stirrup.
Final steps and checks for installing the SkyPanel fixture.
Explains pan/tilt functionality and accessory mounting.
Procedure for mounting a barndoor.
Covers DMX, USB, Ethernet interfaces and control methods.
Guide for connecting the SkyPanel to AC power.
How to connect/disconnect the PowerCON cable.
How to connect/disconnect the XLR cable.
Instructions for powering the SkyPanel using a battery pack.
How to connect/disconnect the 4-pin XLR battery cable.
Advice for optimal battery pack usage.
Introduction to the fixture menu interface and its features.
Controls intensity and navigates the fixture menu.
Adjusts color and accesses presets.
Controls mode, display, menu navigation, and locking.
Adjusts color temperature and saturation.
Configures brightness and dimming curves.
How to enable special control modes like Low End or Tungsten.
Configures fixtures to mimic a master unit.
Settings for DMX address and protocol.
Configures fixture behavior when DMX signal is lost.
Selects fan speed mode for cooling.
Activates built-in lighting demo sequences.
Configures display illumination, brightness, and contrast.
Sets voltage threshold for low battery warning.
Saves and loads fixture presets to/from USB.
Saves and loads fixture configuration settings.
Loads saved fixture settings from USB.
Saves error and service logs to USB.
Displays detailed fixture information.
Resets the fixture to its original factory default settings.
Details on color control modes like CCT, HSI, RGBW.
Explains GEL and XY coordinate control modes.
Setting Art-Net IP and understanding network terms.
Configuring merge mode and gateway.
Advice for reliable DMX data transmission.
Steps to connect the DMX data link.
Table of DMX and fan mode settings.
Options for light mode selection.
Controls dimming curves, special modes, and master/slave.
Activates built-in lighting effects.
Configures display illumination, brightness, contrast, rotation, error mode.
Manages presets, settings, and logs via USB.
Parameters for configuring Art-Net network settings.
Displays detailed fixture information.
Configures battery warning, IP, display version, and USB mode.
Resets the fixture to factory defaults.
Commands for discovering devices and parameters.
Commands for device information.
DMX addressing and fixture identification commands.
Commands for fixture state, defaults, and self-testing.
Manufacturer-specific RDM commands for fan and LEDs.
Configures fixture behavior when DMX signal is lost.
Errors related to temperature, supply, calibration, and calculation.
Errors related to fan, menu, sensors, and LEDs.
Errors related to temperature, voltage, driver, and file system.
DMX channel mapping for 8-bit modes.
DMX channel mapping for 16-bit modes.
DMX channel mapping for coarse/fine modes.
DMX mapping for CCT & RGBW (8-bit).
DMX mapping for CCT (8-bit).
DMX mapping for CCT & HSI (8-bit).
DMX mapping for RGBW (8-bit).
DMX mapping for HSI (8-bit).
DMX mapping for CCT & RGBW (16-bit).
DMX mapping for CCT (16-bit).
DMX mapping for CCT & HSI (16-bit).
DMX mapping for RGBW (16-bit).
DMX mapping for HSI (16-bit).
DMX mapping for CCT & RGBW (Coarse/Fine).
DMX mapping for CCT (Coarse/Fine).
DMX mapping for CCT & HSI (Coarse/Fine).
DMX mapping for RGBW (Coarse/Fine).
DMX mapping for HSI (Coarse/Fine).
Formulas for converting CCT values to DMX.
DMX channel mapping for GEL mode (8-bit).
Information on Gel 1 and Gel 2 settings.
Defines types of gel transitions.
Selection and matching for Gel 2.
DMX channel mapping for GEL mode (16-bit).
Detailed list of Rosco color correction gels.
Selection of gels and Rosco reference.
List of Rosco CalColor gels.
List of Rosco Storaro Selection gels.
List of Rosco Cinelux gels.
Continued list of Rosco Cinelux gels.
List of LEE Color Correction gels.
Continued list of LEE Color Correction gels.
List of LEE Color Filters gels.
Continued list of LEE Color Filters.
List of LEE 600 Series gels.
List of LEE Cosmetic Filters gels.
List of LEE 700 Series gels.
DMX mapping for XY coordinates (8-bit).
DMX mapping for XY coordinates (16-bit).
Physical dimensions, weights, and optical path details.
Power, optical, and control specifications.
Details on control and programming interfaces.
Details on construction, installation, and connectors.
Electrical, power, and thermal specifications.
Product safety and regulatory approvals.
Information on ordering different SkyPanel versions and accessories.
Specifications for PSUs and cables.
Order codes for SkyPanel S30 and S60 models.
Order codes for SkyPanel S120 models.
Specifications for mounting accessories.
Guide to general accessories.
To Next Page
