To Next PageTo Next Page
Need help?Do you have a question about the Arrow HM10867 and is the answer not in the manual?
Key dimensions for the storage building, including approximate size, foundation, storage area, and exterior/interior measurements.
Understand local codes, study the manual for easier, enjoyable construction.
Review all instructions, follow step sequence for successful assembly.
Building must be anchored; level base needed. Recommends Arrow kits or custom solutions.
Verify all parts against the list. Contact customer service for missing items.
Choose dry, calm weather. Two or more people improve assembly efficiency.
Lists required and optional tools, plus base preparation materials.
Choose a level area with good drainage and adequate working space. Prepare base and anchoring system before assembly.
Wear gloves, eye protection, and long sleeves. Exercise caution with tools.
Keep children/pets away. Do not assemble with missing parts or in high winds. Never stand on the roof.
Clean and wax exterior. Keep roof clear of debris; consider snow kits.
Keep door tracks clear. Lubricate annually. Check and retighten fasteners regularly.
Use vapor barrier for condensation. Wash part numbers. Use silicone caulking for seals.
Roof strengthening, anchor kits, tool racks, floor frames, attic kits, and shelf units.
Recommended kit for a base, used with plywood deck or sand fill.
DIY platform using lumber and plywood. Requires level construction.
DIY slab at least 4" thick. Requires gravel, plastic sheeting, and concrete mix.
Describes anchoring to wood/posts and concrete using specific kits and hardware.
Lists various screws, nuts, bolts, handles, washers, and specialized parts like door slides and trim caps.
Detailed list of all parts with key numbers, descriptions, and quantities for assembly.
Assemble front floor frames, center ramp, and join frames with screws.
Overlap and join side and rear floor frames with bolts.
Overlap and fasten rear wall channel pieces and rear wall angle pieces with bolts.
Overlap and fasten side wall channel pieces and side wall angle pieces with bolts.
Fit roof beam pieces together to form four sets; do not insert bolts yet.
Join two sets of beams into a doubled main roof beam with 14 bolts.
Join remaining two sets into left and right roof beam assemblies with 8 bolts each.
Join door track pieces end-to-end with a splice and secure with screws.
Position door slides onto the legs of the door track assembly.
Assemble the four corners of the floor frame using screws and bolts.
Measure diagonals to ensure the floor frame is square and level.
Place corner panels on the floor frame, ensuring widest part is outward, and fasten.
Attach front wall panels to front corners and wall panels to rear corners.
Double-check part numbers of wall panels before proceeding.
Fasten rear wall angle and channel assemblies to the inside top and middle of the rear wall.
Fasten side wall angles and channel assemblies to the inside of side panels.
Fasten the door track assembly to the top of the front wall panels.
Locate and align wall panels, checking hole alignment for correct positioning.
Fasten wall panels at the top, bottom, and center to the wall channel.
Position and fasten front wall channels between side wall channels and corner panels.
Fasten door jambs to front panels using bolts, nuts, and screws, securing to door track and frame.
Attach four roof beam brackets to the gables using bolts, washers, and nuts.
Lift and fasten right and left gables to the door track and rear wall angle.
Join the left and right gables using a gable brace with a bolt and nut.
Repeat steps for the front of the building, using track supports.
Spread and fasten the main roof beam halves to the front and rear gable braces.
Fasten the single roof beams to the structure using bolts and nuts.
Locate roof panels by number, noting sequence and position for installation.
Place the right roof panel at the back right corner, fasten to gable and roof beams.
Install left roof panels at rear corners and a right roof panel at the front corner.
Cut and apply weather stripping tape to the ridge opening as roof panels are installed.
Install remaining narrow and wide roof panels, continuing weather stripping at the ridge.
Install the first ridge cap, fastening overlaps and covering bolt heads with tape.
Install the second ridge cap while installing remaining narrow roof panels, continuing ridge weather stripping.
Fasten the lower ends of panels to side wall angles using screws, bolts, and nuts.
Attach right and left side roof trim to the lower end of roof panels at overlaps.
Overbend side trim flanges inward to fit roof trim caps onto corners.
Fasten roof panel ribs, peak caps, and ridge caps together with bolts and nuts.
Attach door handle brace and handle to the door with a bolt, then swing brace up and secure with a screw.
Hold vertical door brace against the inside surface and fasten with screws.
Place horizontal door brace and attach lower door guides and bolts.
Place the bottom of the right door assembly behind the door jamb into the front frame track.
Position door top, align holes, and fasten doors to slides using screws. Use middle holes for adjustment.
Repeat steps 1 through 3 for the left door.
Rust is natural oxidation of bare metal from moisture, often at screw holes or nicks.
Avoid scraping, use washers, keep clean, and touch up scratches/rust promptly.
General| Capacity | 70 cu ft |
|---|---|
| Material | Galvanized Steel |
| Color | Anthracite/Flint |
| Assembly Required | Yes |
| Weight | 189 lbs |
| Lockable | Yes |
| Weather Resistance | Weather Resistant |
| Storage Capacity | 70 cu ft |
