Atag DW7114XB - User Manual

Questions and Answers

H
Heidi DanielsAug 19, 2025
Why won't my Atag DW7114XB Dishwasher start?
- M
  Michael WilliamsAug 19, 2025
  Your Atag Dishwasher might not start for several reasons. Ensure the Start/Stop button is pressed and held until the display indicates the program has started. Check that the door is properly closed and the door lock has clicked into place. Also, verify that a fuse or circuit breaker hasn't tripped, the plug is securely in the wall socket, and the water tap is turned on. If you hear a whirring sound that doesn't stop when the power is off, turn off the water tap, pull out the plug, and call for service. If the delayed start option is enabled, press and hold Start/Stop for three seconds to cancel it. If you opened the dishwasher mid-cycle, simply close the door and wait for it to resume. Finally, check for any overflow or leaks.
S
Samantha CarrilloAug 21, 2025
How to get my Atag DW7114XB to clean dishes better?
- K
  Kimberly NewmanAug 22, 2025
  If your dishes aren't coming out clean from your Atag Dishwasher, consider these points: * Make sure the spray arms aren't blocked by dishes and can rotate freely. * Clean the spray arms if the holes or bearings are blocked. * Select a program with Intensive mode for very dirty dishes. * Ensure you're using the correct detergent dosage based on water hardness. * Avoid using old detergent. * Load dishes correctly, avoiding overcrowding or covering items. * Ensure glasses and cups are stable. * Check that the filters are correctly fitted and the drainage pump stop is in place.
G
Gerald MaldonadoAug 25, 2025
How to improve drying in my Atag DW7114XB?
- D
  Darlene MyersAug 25, 2025
  To improve drying in your Atag Dishwasher, make sure the Auto Open option is activated. Ensure that the dishwasher is fully loaded. Check that the rinse aid is topped up and the dosage is appropriately set. If you are using all-in-one detergents, consider switching to separate detergents with salt and rinse aid, or deactivate the setting TAB.
E
Edwin JonesAug 27, 2025
What to do if water is left in my Atag Dishwasher?
- V
  vriosAug 27, 2025
  If water remains in your Atag Dishwasher, start by cleaning the coarse and fine filters. Ensure the filters are correctly fitted with the handle locked in the stop position. Clean any debris from the drainage pump. Verify the drainage pump stop is in place. Check the drainage hose for kinks or blockages, ensuring it's properly connected and has an inner diameter of at least 14 mm.
T
Tara MartinAug 28, 2025
Why are there spots or films on dishes from my Atag Dishwasher?
- J
  Jennifer MooreAug 28, 2025
  Spots or films on dishes from your Atag Dishwasher can be due to several factors. Check and adjust the rinse aid dosage setting. If using all-in-one detergents with the TAB setting activated, try switching to separate detergents with salt and rinse aid, or deactivate the TAB setting. Ensure the salt compartment is full and the water softener setting is correct. Also, verify that the salt compartment lid is properly tightened. If washing crystal, use a lower temperature and less detergent.
J
Jason GoodmanAug 30, 2025
How to remove grease deposits from my Atag DW7114XB?
- G
  Gregory Lane PhDAug 30, 2025
  To address grease deposits in your Atag Dishwasher, select a program with Intensive mode to dissolve grease with a higher temperature. Alternatively, run a self-cleaning program once or twice a month.
B
Brad LloydSep 1, 2025
How to remove sticky white/blue film from dishes in my Atag DW7114XB?
- L
  Larry KramerSep 1, 2025
  To remove a sticky white/blue film from dishes in your Atag Dishwasher, reduce the rinse aid dosage. If you have very soft water, you may want to dilute the rinse aid 50:50 with water.
S
Sarah CarterSep 3, 2025
How to fix an Atag DW7114XB door that won't close?
- M
  Mr. Anthony FrancisSep 3, 2025
  If you're having trouble closing the door of your Atag Dishwasher, first check that the baskets are correctly positioned horizontally. Ensure that dishes are not blocking the baskets from sliding properly into place. If the door lock isn't clicking, open the door, then press and hold the left navigation button and the Auto Open option button until the display flashes, wait until it stops (60 seconds), and then close the door to see if the lock engages.
N
nicholasharveySep 5, 2025
How to get rid of bad odour in Atag Dishwasher?
- S
  Spencer GuerreroSep 6, 2025
  To eliminate bad odors in your Atag Dishwasher, clean around the seals and in corners with a washing-up brush and low-foaming cleaner. If you frequently use low-temperature programs, run a high-temperature program or a self-cleaning program once or twice a month.
W
Warren WilliamsSep 8, 2025
What to do if Atag DW7114XB buttons don't react?
- E
  Eric PhillipsSep 8, 2025
  If the buttons on your Atag Dishwasher aren't responding, wait a moment and try again if you've just opened the door. If the child lock is activated, refer to the Settings chapter to deactivate it. Ensure the door is open, as the buttons only work when the door is open. Clean the buttons with a dry or slightly damp cloth if they are dirty.

Atag DW7114XB Specifications

General

Type	Freestanding
Place Setting Capacity	14
Delay Start	Yes
Half Load Option	Yes
Child Lock	Yes
Annual Water Consumption	2520 litres
Dimensions (H x W x D)	85 x 60 x 60 cm