Atag DW7113XA User Manual (English)

Questions and Answers:

J
Joanna OrtizAug 27, 2025
How to fix the Atag Dishwasher door that won't close?
- G
  gmartinAug 27, 2025
  If you're having trouble closing the door of your Atag Dishwasher, here's what to check: * Make sure the baskets are correctly positioned horizontally. * Ensure that dishes aren't blocking the baskets from sliding into place. * If the door lock isn't clicking, open the door. Press and hold the navigation button and the Auto Open option button until the display starts flashing. Wait until it stops flashing (60 seconds). Then, close the door and check that the lock clicks into place.
K
kyle87Aug 28, 2025
What causes spots on stainless steel or silver in my Atag Dishwasher?
- S
  Steven ChavezAug 28, 2025
  Spots on stainless steel or silver in your Atag Dishwasher can be caused by: * Certain foods like mustard, mayonnaise, lemon, vinegar, salt, and dressings can cause spots if left on items for too long. Rinse these foods off dishes if you're not starting the dishwasher immediately, or use the Rinse & hold program. * Contact between different metals (stainless steel and silver) during dishwashing. Separate dishes made from different metals to avoid marks and tarnishing.
M
Michael KruegerAug 29, 2025
What causes sticky white/blue film on dishes from Atag Dishwasher?
- B
  blackcrystalAug 29, 2025
  The rinse aid dosage setting is too high. Reduce the dosage. If you have very soft water, you may want to dilute the rinse aid 50:50 with water.
B
Benjamin ToddAug 31, 2025
How to remove spots left after washing in Atag DW7113XA Dishwasher?
- A
  Andrew MendozaAug 31, 2025
  Lipstick and tea can be difficult to wash off. Use a detergent with a bleaching agent.
P
Penny BondSep 1, 2025
What to do if there's water left in my Atag Dishwasher?
- J
  Jenna JacobsSep 1, 2025
  If water remains in your Atag Dishwasher, check the following: * The filters might be blocked; clean the coarse and fine filters. * The filters might not be fitted correctly; ensure the filter handle is locked in the stop position. * There might be debris in the drainage pump; clean the drainage pump. * The drainage pump stop might be missing; check that the coloured stop is in place at the bottom drain. * There might be a kink in the drainage hose; ensure it's free from kinks and sharp bends. * The drainage hose might be blocked; disconnect it from the sink unit's water trap and check for debris, ensuring the connection has at least a 14 mm inner diameter.
A
Alyssa AvilaSep 2, 2025
Why aren't my dishes drying in my Atag DW7113XA Dishwasher?
- R
  Ronnie JohnstonSep 2, 2025
  If your dishes aren't drying in your Atag Dishwasher, here's what to check: * The Auto Open option isn't activated; activate it. * The dishwasher isn't fully loaded; fully load it. * The rinse aid needs topping up or the dosage is too low; top it up or increase the dosage. * The setting TAB is activated, and all-in-one detergent with an insufficient drying effect is being used; switch detergents or deactivate the setting TAB and add salt and separate rinse aid.
K
Kathryn OlsonSep 3, 2025
How do I remove spots or films from dishes in my Atag DW7113XA?
- M
  Mrs. Danielle Welch DDSSep 3, 2025
  Spots or films on dishes from your Atag Dishwasher can be due to: * Incorrect rinse aid dosage; adjust the setting. * The TAB setting is activated with all-in-one detergent that has an insufficient drying effect; switch detergents or deactivate the TAB setting and add salt and rinse aid separately. * An empty salt compartment; top it up with salt. * Incorrect water softener setting; adjust the water hardness setting. * The water softener is leaking salt; ensure the salt compartment lid is tightened, otherwise call for service. * Too high temperature and/or too much detergent causing etching on crystal; wash crystal at a low temperature with less detergent.
R
Richard MartinezSep 4, 2025
What to do if the buttons on my Atag DW7113XA Dishwasher aren't responding?
- L
  Lisa HallSep 4, 2025
  If the buttons on your Atag Dishwasher aren't responding, it could be due to: * Pressing the buttons too soon after opening the door; wait a moment and try again. * The child lock being activated; see the chapter Settings for deactivation instructions. * The door being closed; open the door as the buttons only work when the door is open. * The buttons being dirty; clean them with a dry or slightly damp cloth.
D
Dr. Lori DavisSep 5, 2025
How to prevent spots on stainless steel or silver in my Atag DW7113XA Dishwasher?
- S
  Scott RhodesSep 6, 2025
  Spots on stainless steel or silver in your Atag Dishwasher can occur because: * Some foods like mustard, mayonnaise, lemon, vinegar, salt, and dressings can cause spots if left too long; rinse these off if not starting the dishwasher immediately and use the Rinse & hold program. * Contact between stainless steel and silver during washing can cause spots; separate dishes made from different metals to avoid marks and tarnishing.
P
perezjustinSep 6, 2025
How to prevent dishes from being not dry enough in my Atag DW7113XA Dishwasher?
- R
  Randy FrazierSep 7, 2025
  If your dishes aren't drying properly in your Atag Dishwasher, here are a few things to try: * Make sure the Auto Open option is activated. * Ensure the dishwasher is fully loaded. * Check the rinse aid level and dosage. Top up the rinse aid or increase the dosage if needed. * If you're using all-in-one detergent with the TAB setting activated and it's not drying effectively, switch to separate detergents and deactivate the TAB setting. Add salt and rinse aid separately.

Atag DW7113XA Specifications

General

Type	Freestanding
Colour	Stainless Steel
Number of place settings	13
Number of programs	6
Energy efficiency class	A++
Annual Energy Consumption	262 kWh
Drying Efficiency Class	A
Delay Start	Yes
Half Load Option	Yes
Dimensions (HxWxD)	85 x 60 x 60 cm