What causes rattling sound when dishwashing in Atag DW8114XT/A01 Dishwasher?
If you notice a rattling sound when your Atag Dishwasher is running, make sure the dishes are placed securely and that the spray arms can rotate freely.
How to fix Atag DW8114XT/A01 Dishwasher if the dishes are not clean?
If your Atag Dishwasher isn't cleaning dishes properly, several factors could be at play. Ensure the spray arms aren't blocked by dishes and can rotate freely. Clean the spray arms and middle basket's spray pipes. Select a program with Intensive mode for heavily soiled dishes. Check your detergent dosage, using the correct amount for your water hardness, and ensure your detergent isn't old. Load the dishes correctly, avoiding overcrowding or blocking. Make sure glasses and cups are stable. Verify the filters are correctly fitted and that the drainage pump stop is in place.
Why does my Atag Dishwasher leave spots or films on the dishes?
If your Atag Dishwasher leaves spots or films on the dishes, the cause could be an incorrect rinse aid dosage. Refer to the Settings section to adjust it. If you're using all-in-one detergent with the TAB setting activated but the drying effect is insufficient, switch detergents or deactivate the TAB setting and add salt and separate rinse aid. Ensure the salt compartment is full and the water softener setting is correct. Check the salt compartment lid is tightened properly. If you notice etching on crystal, wash crystal at a low temperature with a conservative amount of detergent.
How to improve drying in my Atag DW8114XT/A01?
If your Atag Dishwasher leaves dishes not dry enough, ensure the Auto Open option is activated. Make sure the dishwasher is fully loaded for optimal drying. Check the rinse aid level and increase the dosage if necessary. If you are using all-in-one detergents with the TAB setting activated but the drying effect is insufficient, switch detergents or deactivate the TAB setting and top up with salt and separate rinse aid.
What to do if water remains in my Atag Dishwasher?
If you find water remains in your Atag Dishwasher after a cycle, start by cleaning the coarse and fine filters. Ensure the filters are correctly fitted and locked in position. Check for any debris in the drainage pump and clean it if necessary. Verify the drainage pump stop is in place. Inspect the drainage hose for kinks or blockages, ensuring it has a clear inner diameter of at least 14 mm where it connects to the sink unit's water trap.
Why is there detergent residue in the detergent compartment of my Atag Dishwasher?
If you're finding detergent residue in the detergent compartment of your Atag Dishwasher after washing, ensure the compartment is dry when you add detergent. Also, check that dishes aren't blocking the detergent compartment from opening properly.
Why are there spots on stainless steel or silver in my Atag DW8114XT/A01 Dishwasher?
If you notice spots on stainless steel or silver items in your Atag Dishwasher, it may be due to prolonged contact with certain foodstuffs like mustard, mayonnaise, lemon, vinegar, or salt. Rinse these foods off dishes if you're not starting the dishwasher immediately, or use the Rinse and hold program. To prevent contact corrosion, separate dishes made from different metals like silver, stainless steel, and aluminum.
Why does my Atag DW8114XT/A01 leave a sticky white/blue film?
If your Atag Dishwasher leaves a sticky white/blue film on the dishes, it could be due to a rinse aid dosage setting that's too high. Reduce the dosage; see the Settings chapter for instructions. If you have very soft water, consider diluting the rinse aid 50:50 with water.
Why does water remain in my Atag Dishwasher?
If water remains in your Atag Dishwasher after a cycle, check the following: * Clean the coarse and fine filters. * Ensure the filters are correctly fitted and the filter handle is locked in the stop position. * Clean any debris from the drainage pump. * Verify the drainage pump stop is in place. * Check the drainage hose for kinks or sharp bends. * Ensure the drainage hose is not blocked.
Why are the dishes not clean in my Atag Dishwasher?
If your Atag Dishwasher isn't cleaning dishes properly, consider these potential causes: * Make sure that dishes aren't blocking the spray arms. * Clean the spray arms and middle basket spray pipes if they are blocked. * Select a program with Intensive mode for very dirty dishes. * Ensure you are using the correct detergent dosage based on water hardness. * Avoid using old detergent. * Load the dishes correctly, avoiding overcrowding. * Ensure dishes are placed to sit steadily. * Check that the filter handle is locked in the stop position. * Ensure the colored stop on the right in the bottom drain is in place.
General| Brand | Atag |
|---|---|
| Model | DW8114XT/A01 |
| Category | Dishwasher |
| Language | English |
To Next Page
