Why is my Atag DW7114SXB Dishwasher making a rattling sound?
If you hear a rattling sound when your Atag dishwasher is running, it's likely because: * The dishes are not placed correctly, or the spray arms are not rotating freely. Make sure the dishes are placed securely and spin the spray arms to ensure they can rotate without obstruction.
How to fix Atag Dishwasher when the dishes are not clean?
The dishes may not be clean because the spray arms are blocked by the dishes. Ensure that the dishes are not blocking the spray arms. Also, the spray arm holes or bearings may be blocked. Clean the spray arms. An unsuitable dishwashing program, incorrect detergent dosage, or old detergent may also cause this problem. Select a program with Intensive mode, dose according to water hardness, and avoid large packages of detergent. Make sure that you do not cover porcelain with large bowls or place very tall glasses in the corners of the baskets and place dishes to sit steady. Check that the filter handle is locked in the stop position and that the coloured stop on the right in the bottom drain is in place.
Why are the dishes not dry enough in my Atag DW7114SXB?
The dishes may not be dry enough because the Auto Open option is not activated. Activate the Auto Open option. Also, the dishwasher may not be fully loaded. Fully load the dishwasher. The rinse aid may need topping up or the dosage may be set too low. Top up with rinse aid or increase the rinse aid dosage level. If the setting TAB is activated and all-in-one detergent with insufficient drying effect is being used, switch all-in-one detergents or deactivate the setting TAB and top up with salt and separate rinse aid.
What to do if water remains in the Atag DW7114SXB after cycle?
If water remains in the Atag dishwasher, the filters may be blocked. Clean the coarse and fine filters. The filters may also not be fitted correctly. Check that the filter handle is locked in the stop position. Debris in the drainage pump, a missing drainage pump stop, a kink in the drainage hose, or a blocked drainage hose can also cause this issue. Clean the drainage pump, check that the coloured stop on the right in the bottom drain is in place, check that the hose is free from kinks and sharp bends, and disconnect the drainage hose where it connects to the sink unit's water trap to check for blockages.
How to get rid of bad odour in Atag DW7114SXB Dishwasher?
A bad odour in the Atag dishwasher may be due to dirt around the seals and in corners. Clean with washing-up brush and low foaming cleaner. Also, low temperature programs may have been selected for a prolonged period. Run a program with a high temperature once or twice a month. Or run a self-cleaning program.
How to fix an Atag DW7114SXB door that won't close?
If you're having trouble closing the door of your Atag dishwasher: * Make sure the baskets are correctly positioned horizontally. * If the door lock isn't clicking into place, open the door. Press and hold the left navigation button and the Auto Open option button until the display starts flashing. Wait until it stops flashing (60 seconds). Close the door and check that the door lock clicks into place.
How to get rid of bad odour in my Atag Dishwasher?
If you notice a bad odor coming from your Atag dishwasher, it could be due to: * Dirt around the seals and in corners. Clean these areas with a washing-up brush and a low-foaming cleaner. * Prolonged use of low-temperature programs. Try running a high-temperature program once or twice a month, or use the self-cleaning program.
What to do if the buttons on my Atag DW7114SXB Dishwasher don't react?
If the buttons on your Atag dishwasher aren't responding, it could be due to a few reasons: * You might be pressing the buttons too soon after opening the door. Wait a moment and try again. * The child lock (button lock) might be activated. See the chapter Settings for instructions on deactivating it. * The door might be closed. The buttons only work when the door is open. * The buttons might be dirty. Clean them with a dry or slightly damp cloth.
How to remove grease deposits from my Atag DW7114SXB?
If you're finding grease deposits in your Atag dishwasher, it's likely due to: * Using low-temperature programs for an extended period. Try selecting a program with Intensive mode, which uses a higher temperature to dissolve grease on heavily soiled dishes. Alternatively, run a self-cleaning program once or twice a month.
Why is my Atag Dishwasher making a rattling sound when dishwashing?
A rattling sound when dishwashing in your Atag Dishwasher may be because the dishes are not correctly placed or the spray arms are not rotating. Check that the dishes are placed securely. Spin the spray arms to make sure they can rotate.
General| Type | Freestanding |
|---|---|
| Place settings | 14 |
| Water consumption per cycle | 9.5 L |
| Width | 60 cm |
| Delay Start | Yes |
| Half Load Option | Yes |
| Child Lock | Yes |
| Dimensions (H x W x D) | 85 cm x 60 cm x 60 cm |
To Next Page
