Atag DW8214MB - User Manual

Questions and Answers

J
James DanielsAug 18, 2025
Why my Atag Dishwasher does not start?
- T
  Teresa FlemingAug 18, 2025
  If your Atag dishwasher doesn't start, there are several possible reasons. First, make sure the door is properly closed. If you opened the dishwasher mid-cycle to add dishes, close the door and wait for the program to resume. Check that the door lock clicks into place; if it doesn't, open the door, press and hold until the display flashes, wait 60 seconds, then close the door again. Also, ensure the dishwasher is plugged into the wall socket and that the fuse/circuit breaker hasn't tripped. If the 'Delayed start' option is selected, press and hold for three seconds to cancel it. Lastly, press until the display shows 'Program started'.
K
Kenneth RobinsonAug 20, 2025
How to fix Atag DW8214MB that leaves dishes not clean?
- S
  Shelly HarrisAug 21, 2025
  If your dishes aren't clean after running your Atag dishwasher, several factors could be at play. Ensure the spray arms can rotate freely and aren't blocked by dishes. Clean the spray arms if the holes or bearings are blocked. Select a suitable dishwashing program, like 'Intensive' for very dirty dishes, to dissolve grease effectively. Check the detergent dosage, using the correct amount based on your water hardness, and make sure your detergent isn't old. Load dishes correctly, avoiding overcrowding or covering items, and ensure glasses and cups are stable. Lastly, clean the coarse and fine filters and make sure they are correctly fitted, and verify that the yellow drainage pump stop is in place.
N
Nicholas SmithAug 23, 2025
What to do if water remains in Atag Dishwasher?
- E
  Edward EdwardsAug 23, 2025
  If water remains in your Atag dishwasher after a cycle, check the following: Clean the coarse and fine filters, and ensure they are correctly fitted. Inspect the drainage pump for debris and clean it if necessary. Verify the yellow drainage pump stop is in place. Examine the drainage hose for kinks or blockages, ensuring it has an inner diameter of at least 14 mm where it connects to the sink unit's water trap.
K
krystalmyersAug 26, 2025
How to remove spots or films on dishes from Atag Dishwasher?
- L
  Lisa YoungAug 26, 2025
  If you notice spots or films on dishes washed in your Atag dishwasher, it could be due to several reasons. Check and adjust the rinse aid dosage setting. If using all-in-one detergent with the 'TAB' setting activated, consider switching detergents or deactivating the setting and adding salt and separate rinse aid. Ensure the salt compartment is full and the water softener setting is correct. Verify the salt compartment lid is tightened properly. If washing crystal, use a low temperature and less detergent to prevent etching.
N
nicole18Aug 28, 2025
How to remove grease deposits in Atag Dishwasher?
- J
  Jeffrey WilsonAug 28, 2025
  To address grease deposits in your Atag dishwasher, select a high-temperature program, such as the Intensive program, for very dirty dishes to dissolve the grease. Alternatively, run a self-cleaning program once or twice a month.
J
Joseph WhiteAug 30, 2025
How to remove sticky white/blue film from dishes in Atag DW8214MB Dishwasher?
- E
  Erin FarmerAug 30, 2025
  If your dishes have a sticky white or blue film after washing in your Atag dishwasher, the rinse aid dosage setting might be too high. Reduce the dosage. If you have very soft water, consider diluting the rinse aid 50:50 with water.
C
Charles LeeSep 2, 2025
How to remove spots left after washing in Atag DW8214MB Dishwasher?
- S
  Susan GordonSep 2, 2025
  If you notice spots left after washing in your Atag dishwasher, especially from lipstick or tea, try using a detergent with a bleaching agent.
R
Robert SanchezSep 5, 2025
Why Atag Dishwasher leaves dishes not dry enough?
- M
  meganmedinaSep 5, 2025
  If your dishes are not drying properly in your Atag dishwasher, try these solutions: Activate the 'Auto door open' option. Make sure you fully load the dishwasher. Check the rinse aid level and dosage, topping up if necessary or increasing the dosage setting. If you're using all-in-one detergents with the 'TAB' setting activated, switch to separate detergents or deactivate the setting and add salt and rinse aid.
A
andradeanthonySep 7, 2025
How to get rid of bad odour in Atag DW8214MB?
- D
  desiree78Sep 7, 2025
  If there's a bad odor coming from your Atag dishwasher, it might be due to dirt around the seals and in corners; clean these areas with a washing-up brush and a low-foaming cleaner. Also, if you've been using low-temperature programs for a long time, run a high-temperature program once or twice a month, or use the self-cleaning program.
T
Thomas MillerSep 9, 2025
What to do if I cannot close the door of Atag DW8214MB Dishwasher?
- R
  Richard MooneySep 9, 2025
  If you cannot close the door of your Atag dishwasher, check that the baskets are positioned correctly horizontally. If the door lock doesn't click into place, open the door, press and hold until the display flashes, wait 60 seconds, and then close the door again to ensure the lock clicks.