Why is there grease buildup in my Atag Dishwasher?
Grease deposits in your Atag Dishwasher are likely due to: * Prolonged use of low temperature programs; select a high temperature program to dissolve grease on very dirty dishes.
What causes rattling sound when dishwashing in Atag Dishwasher?
A rattling sound during dishwashing in your Atag Dishwasher indicates that the dishes are not correctly placed or the spray arms are not rotating. Check that the dishes are placed securely and spin the spray arms to ensure they can rotate freely.
What to do if there is water remaining in my Atag DW7113XA?
If water remains in your Atag Dishwasher after a cycle, check the following: * The filters may be blocked. Clean the coarse and fine filters. * The filters may not be fitted correctly. Ensure the filter handle is locked in the stop position, pointing straight out from the dishwasher. * There might be debris in the drainage pump. Clean the drainage pump. * The drainage pump stop might be missing. Check for the colored stop on the right in the bottom drain. * There could be a kink in the drainage hose. Ensure the hose is free from kinks and sharp bends. * The drainage hose might be blocked. Disconnect the drainage hose from the sink unit's water trap and check for debris, ensuring the connection has an inner diameter of at least 14 mm.
How to fix the Atag Dishwasher door that won't close?
If you're having trouble closing the door of your Atag Dishwasher, here's what to check: * Make sure the baskets are correctly positioned horizontally. * Ensure that dishes aren't blocking the baskets from sliding into place. * If the door lock isn't clicking, open the door. Press and hold the navigation button and the Auto Open option button until the display starts flashing. Wait until it stops flashing (60 seconds). Then, close the door and check that the lock clicks into place.
What causes grease deposits in the Atag Dishwasher?
Grease deposits in your Atag Dishwasher may appear if low temperature programs have been selected for a prolonged period. Select a program with a high temperature to dissolve grease on very dirty dishes, such as Intensive.
Why does my Atag DW7113XA have a bad odor?
A bad odor in your Atag Dishwasher can be caused by: * Dirt around the seals and in corners. Clean these areas with a washing-up brush and a low-foaming cleaner. * Using low-temperature programs for extended periods. Run a high-temperature program once or twice a month.
Why do the buttons on my Atag DW7113XA Dishwasher not react when pressed?
If the buttons on your Atag Dishwasher aren't responding, it could be due to a few reasons: * You might be pressing the buttons too soon after opening the door. Wait a moment and try again. * The child lock (button lock) might be activated. Please refer to the Settings section for deactivation instructions. * The buttons only work when the door is open. Make sure the door is open when trying to use the buttons. * The buttons may be dirty. Clean them with a dry or slightly damp cloth.
How to prevent dishes from being not dry enough in my Atag DW7113XA Dishwasher?
If your dishes aren't drying properly in your Atag Dishwasher, here are a few things to try: * Make sure the Auto Open option is activated. * Ensure the dishwasher is fully loaded. * Check the rinse aid level and dosage. Top up the rinse aid or increase the dosage if needed. * If you're using all-in-one detergent with the TAB setting activated and it's not drying effectively, switch to separate detergents and deactivate the TAB setting. Add salt and rinse aid separately.
How to prevent spots on stainless steel or silver in my Atag DW7113XA Dishwasher?
Spots on stainless steel or silver in your Atag Dishwasher can occur because: * Some foods like mustard, mayonnaise, lemon, vinegar, salt, and dressings can cause spots if left too long; rinse these off if not starting the dishwasher immediately and use the Rinse & hold program. * Contact between stainless steel and silver during washing can cause spots; separate dishes made from different metals to avoid marks and tarnishing.
What to do if the buttons on my Atag DW7113XA Dishwasher aren't responding?
If the buttons on your Atag Dishwasher aren't responding, it could be due to: * Pressing the buttons too soon after opening the door; wait a moment and try again. * The child lock being activated; see the chapter Settings for deactivation instructions. * The door being closed; open the door as the buttons only work when the door is open. * The buttons being dirty; clean them with a dry or slightly damp cloth.
General| Type | Freestanding |
|---|---|
| Colour | Stainless Steel |
| Number of place settings | 13 |
| Number of programs | 6 |
| Energy efficiency class | A++ |
| Annual Energy Consumption | 262 kWh |
| Drying Efficiency Class | A |
| Delay Start | Yes |
| Half Load Option | Yes |
| Dimensions (HxWxD) | 85 x 60 x 60 cm |
To Next Page
