DESCRIPTION
The Extron DMP 64 Plus series of compact Digital Matrix
Processors features six DSP input channels with AEC, in only a half
rack space. With a flexible mix matrix, a USB audio interface, and
6x4 analog connectivity, the DMP 64 Plus provides the ability to easily
connect and route signals to accommodate system requirements.
The AT models can be powered by PoE+ and provide 32x16
Dante connectivity for popular Dante microphone arrays, and other
Dante devices, while the V models include up to eight VoIP lines for
collaboration applications. Featuring an ACP bus for audio control
panels, an expansion port for bidirectional digital audio connection
with a DTP CrossPoint
®
or another DMP, eight audio file players, and
configurable macros, the DMP 64 Plus can be used in a wide variety
of smaller systems.
Acoustic Echo Cancellation
The DMP 64 Plus series includes Extron AEC for conferencing
applications. AEC is essential for effective remote room-to-room
conversations, ensuring clear, natural communication for all par-
ticipants. These models include six independent channels of high
performance AEC, as well as selectable noise cancellation. AEC
processing can be challenged by conditions such as double-talk,
when talkers from both ends are speaking simultaneously, and
when near end talkers use wireless microphones. Extron AEC
features advanced algorithms that deliver fast echo canceler con-
vergence for optimal intelligibility, even in challenging conditions.
Dante Connectivity
The Dante-equipped DMP 64 Plus AT models provide scalable
audio transport, with Dante Domain Manager support, over a
local area network using standard network protocols. Each
DMP 64 Plus AT model sends out 16 channels of digital audio
and can receive 32 channels over the network, offering easy
connectivity to popular Dante microphones. A built-in two-port
Gigabit switch provides direct connection to other Dante-enabled
devices to create simplified, cost effective audio systems. Addi-
tionally, the DMP 64 Plus AT models can be configured to support
primary and redundant Dante audio networks, as well as AES67
compatibility. Setting up a network of Extron Dante-enabled audio
devices requires Dante Controller, and Extron DSP Configurator
Software.
Power Over Ethernet
The AT models with Dante connectivity can be powered by PoE+.
FlexInputs
All six main DSP channels of the DMP 64 Plus offer FlexInput
source selection to route any Dante input, expansion input, or one
of the six mic/line inputs, to a main DSP channel. This enables the
DMP 64 Plus to process audio from any source with the full range
of DSP capabilities, including AEC.
USB Audio Interface
The configurable USB audio interface provides connectivity to a
computer for use with soft CODEC applications and computer
sourced audio and can be set to 0x8, 2x6, 4x4, 6x2, or 8x0.
This allows for more input or output streams, as required by the
system application.
KEY FEATURES
A Four models with 6 mic/line inputs and 4 line outputs
A Six channels of AEC - acoustic echo cancellation
A All models include a configurable USB Audio interface –
Easy connectivity to computer based soft codecs and program
playback sources. The input/output configuration of the USB
Audio Interface can be set to 0x8, 2x6, 4x4, 6x2, or 8x0.
A AT models provide Dante audio network connectivity –
- Receives 32 channels from a Dante network
- Transmits 16 channels to a Dante network
- Supports Dante Domain Manager
- AES67 support
A V models include up to eight VoIP lines – Supports generic
Session Initiation Protocol - SIP 2.0 connectivity per RFC 3261
A Compact half rack size
A FlexInput capability on main inputs – All six main inputs offer
FlexInput capability to select a Dante channel, expansion input,
or a local mic/line input. This allows incorporating the full range of
DSP capabilities, including AEC, for incoming Dante channels.
A AT models can be powered by PoE+
A Optional ACP Series audio control panels provide intuitive
audio system control – Directly connects to the DMP 64 Plus,
offering flexible audio control for configurations that do not require
a full control system.
A Digital I/O ports for remote control or feedback – Six digital
input and output ports are provided, so that the DMP 64 Plus can
be programmed to sense and then respond to external triggers
such as mic activation, muting, and recall of presets.
A Macros allow the sequencing of commands that can be sent
to the local device or external devices via the LAN port – A
single DMP 64 Plus can act as the central interface from a control
system, sending commands to other DMP and DTP CrossPoint
units.
A Advanced audio processing on all four analog outputs and all
16 direct Dante/Expansion outputs – Up to 20 speaker zones
can be implemented on one DMP 64 Plus with full processing for
each zone, making it ideal for full mix-minus implementations.
A Extensive mix matrixing in every DMP 64 Plus allows all inputs
to be discretely routed to any or all outputs – A 54x28 mix
matrix allows all main inputs, aux inputs, Dante inputs and virtual
bus returns to be discretely routed to any or all of the analog
outputs, aux outputs, Dante outputs and the virtual bus sends.
A 16 virtual processing loops allow for great flexibility in sub-
mixing and processing – Processing common to many inputs
can be applied using a single virtual channel.
A Up to eight audio file players can be used to play back audio
files for system set-up or as part of the system design – Use
the provided pink noise, white noise, and sine wave files, or import
your own WAV, MP3, WMA, AIFF, AAC, or RAW files. Supported
file formats are automatically converted to 24-bit, 48 kHz RAW
for approximately 20 minutes of playback time and saved to the
onboard storage.
To Next Page
Loading...