Audio Technica AT-LPW30TK

13
Specifications
Turntable specifications
Type Belt-drive manual turntable
Motor AT-LPW40WN: DC servo with Active
Speed Stabilization
AT-LPW30TK: DC servo
Drive method Belt drive
Speeds 33-1/3 RPM, 45 RPM
Turntable platter Aluminum Die Casting
Wow and flutter < 0.15 % WRMS (33 RPM) at 3 kHz
Signal-to-noise ratio > 60 dB
Output levels
“PHONO”
“LINE”
4.0 mV nominal at 1 kHz, 5 cm/sec
200 mV nominal at 1 kHz, 5 cm/sec
Phono Pre-amp gain 35 dB nominal, RIAA equalized
Tonearm specifications
Type AT-LPW40WN: Static balanced straight
carbon tonearm
AT-LPW30TK: Static balanced straight
aluminium pipe tonearm
Effective length 223.6 mm
Overhang 18.6 mm
Maximum tracking error angle Less than 2.0°
Stylus pressure adjustment
range
0 to 3.0 g
Applicable cartridge weight
range (including headshell)
12 to 17 g
Cartridge and headshell specifications
Cartridge Model AT-LPW40WN: AT-VM95E
AT-LPW30TK: AT-VM95C
Cartridge Type VM
Recommended load
impedance
47,000 ohms
Output voltage 4.0 mV (mV at 1 kHz, 5 cm/sec)
Stylus AT-LPW40WN: 0.3 × 0.7 mil bonded
elliptical stylus
AT-LPW30TK: 0.6 mil bonded conical
stylus
Cantilever Aluminum pipe
Tracking force range 1.8 to 2.2 g (standard 2.0 g)
Cartridge weight 6.1 g (0.22 oz)
Headshell model AT-HS4
Headshell weight 8.5 g (excluding lead wires)
Headshell overhang
adjustment
± 5 mm
General specifications
Power supply requirements 100 to 240 V, 50/60 Hz, 0.5 A Max.
Power consumption 110V 60Hz (US)
- Working: 1.1 W
- Motor off: 1.0 W
- Power off: 0.1 W
220V 50Hz (EU)
- Working: 1.2 W
- Motor off: 1.1 W
- Power Off: 0.2 W
AC Adapter 12 V, 0.5 A
Dimensions 420 mm (16.53") × 340 mm (13.38")
× 116.9 mm (4.6")
(W × D × H)
Weight (without dust cover) AT-LPW40WN: 4.72 kg (10.40 lbs)
AT-LPW30TK: 3.90 kg (8.60 lbs)
Accessories included Dust cover, Platter, Turntable
mat, Drive belt, Counterweight,
Headshell (AT-HS4) with VM stereo
cartridge*, 45-RPM adapter, RCA
audio cable (Approx. 1.0 m (3.3')),
AC adapter (Approx. 1.5 m (4.9'))
(AD-SA1205WE), Dust cover hinges
Replacement stylus (sold
separately)
AT-LPW40WN: AT-VMN95E
AT-LPW30TK: AT-VMN95C
Replacement headshell (sold
separately)
AT-HS4
Replacement belt (sold
separately)
AT-LPW40WN/AT-LPW30TK exclusive
belt
* AT-LPW40WN: AT-VM95E / AT-LPW30TK: AT-VM95C
Specifications are subject to change without notice due to
improvements.