AutomationDirect D2-16ND3-2

To Next Page

To Previous Page

INTRODUCTION

CHAPTER

In This Chapter...

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1–2

Conventions Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1–3

CPU-slot Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1–4

Main Page

Default Chapter7
- Table of Contents7
Chapter 1: Introduction14
Introduction14
- The Purpose of this Manual14
- Where to Begin14
- Supplemental Manuals14
- Technical Support14
Conventions Used15
- Key Topics for each Chapter15
CPU-Slot Controllers16
DL205 System I/O Components17
- Bases17
- I/O Configuration17
- I/O Modules17
Chapter 2 : Installation and Power Wiring20
Safety Guidelines20
- Plan for Safety20
- Three Levels of Protection21
- Emergency Stops21
- Emergency Power Disconnect22
- Orderly System Shutdown22
- Class 1, Division 2, Approval22
Mounting Guidelines23
- Base Dimensions23
- Panel Mounting and Layout24
- Enclosures25
- Environmental Specifications26
- Power26
- Marine Use27
- Agency Approvals27
- 24 VDC Power Bases27
Installing DL205 Bases28
- Choosing the Base Type28
- Mounting the Base28
- Using Mounting Rails29
Installing Components in the Base30
Base Wiring Guidelines31
- Base Wiring31
Chapter 3: I/O Wiring and Specification34
I/O Wiring Strategies34
- PLC Isolation Boundaries34
- Powering I/O Circuits with the Auxiliary Supply35
- Powering I/O Circuits Using Separate Supplies36
- Sinking / Sourcing Concepts37
- I/O "Common" Terminal Concepts38
- Connecting DC I/O to "Solid State" Field Devices39
- Solid State Input Sensors39
- Solid State Output Loads39
- Relay Output Guidelines41
- Surge Suppression for Inductive Loads41
I/O Modules Position, Wiring, and Specification45
- Slot Numbering45
- Module Placement Restrictions45
- Special Placement Considerations for Analog Modules46
- Discrete Input Module Status Indicators46
- Color Coding of I/O Modules46
- Wiring the Different Module Connectors47
- I/O Wiring Checklist48
- I/O Points Required for each Module49
Calculating the Power Budget50
- Managing Your Power Resource50
- CPU Power Specifications50
- Module Power Requirements50
- Power Budget Calculation Example52
- Power Budget Calculation Worksheet53
DL205 Digital Input Modules54
- D2-16ND3-2, DC Input54
- D2-08ND3, DC Input54
- D2-32ND3, DC Input55
- D2-32ND3-2, DC Input56
- D2-08NA-1, AC Input57
- D2-08NA-2, AC Input58
- F2-08SIM, Input Simulator59
- D2-16NA, AC Input59
- D2-04TD1, DC Output60
DL205 Digital Output Modules60
- D2-08TD2, DC Output61
- D2-08TD1, DC Output61
- D2-16TD2-2, DC Output62
- D2-16TD1-2, DC Output62
- F2-16TD1(2)P, DC Output with Fault Protection63
- F2-16TD1P, DC Output with Fault Protection64
- F2-16TD2P, DC Output with Fault Protection65
- D2-32TD2, DC Output66
- D2-32TD1, DC Output66
- D2-08TA, AC Output67
- F2-08TA, AC Output67
- D2-12TA, AC Output68
- D2-04TRS, Relay Output69
- D2-08TR, Relay Output70
- F2-08TR, Relay Output71
- F2-08TRS, Relay Output72
- D2-12TR, Relay Output73
- D2-08CDR, 4 Pt. DC Input / 4Pt. Relay Output74
Notes75
DL205 Analog Input Modules76
- F2-04AD-1 4-Channel 4-20Ma Analog Input Module76
- F2-08AD-1 8-Channel 4-20Ma Analog Input Module78
- F2-04AD-2 4-Channel Voltage Analog Input Module80
- F2-08AD-2 8-Channel Voltage Analog Input Module82
  - DL205 RTD and Thermocouple Modules84
- F2-04THM 4-Channel Thermocouple Input Module86
  - DL205 Analog Output Modules88
- F2-02DA-1L 2-Channel 4-20Ma Analog Output Module90
- F2-02DAS-1 2-Channel Isolated 4-20Ma Analog Output Module92
- F2-08DA-1 8-Channel 4-20Ma Analog Output Module94
- F2-02DA-2 2-Channel Voltage Analog Output Module96
- F2-02DA-2L 2-Channel Voltage Analog Output Module98
- F2-02DAS-2 2-Channel 0-5V, 0-10V Isolated Analog Output Module100
- F2-08DA-2 8-Channel Voltage Analog Output Module102
  - DL205 Combination Analog I/O Modules104
- Output Module106
- Output Module108
- Maximum Leakage Current111
Appendix A: European Union (EU) Directives113
European Union (EU) Directives113
- Member Countries114
- Applicable Directives114
- Compliance114
- General Safety115
- Special Installation Manual116
- Other Sources of Information116
Basic EMC Installation Guidelines116
- Enclosures116
- AC Mains Filters117
- Suppression and Fusing117
- Internal Enclosure Grounding117
- Equi-Potential Grounding118
- Communications and Shielded Cables118
- Analog and RS232 Cables119
- Shielded Cables Within Enclosures119
- Analog Modules and RF Interference120
- Network Isolation120
- DC Powered Versions120
- Items Specific to the DL205121

AutomationDirect D2-16ND3-2 - Page 13

Table of Contents