Autonics LE4SA - Page 12

K-31
(A)
Photo
electric
sensor
(B)
Fiber
optic
sensor
(C)
Door/Area
sensor
(D)
Proximity
sensor
(E)
Pressure
sensor
(F)
Rotary
encoder
(G)
Connector/
Socket
(H)
Temp.
controller
(I)
SSR/
Power
controller
(J)
Counter
(K)
Timer
(L)
Panel
meter
(M)
Tacho/
Speed/ Pulse
meter
(N)
Display
unit
(O)
Sensor
controller
(P)
Switching
mode power
supply
(Q)
Stepper
motor&
Driver&Controller
(R)
Graphic/
Logic
panel
(S)
Field
network
device
(T)
Software
(U)
Other
LCD Timer(Touch Type)
LE4S Output operation mode
T = Setting time, T > Ta
※
Initial status : UP mode-display value is "0", output is "OFF". DOWN mode-display value is "setting time", output is "OFF".
Mode
Time chart Operation
[
OND
]
POWER
START
RESET
RELAY OUT
Set time
Set time
0
0
UP
DOWN
T T
①
② ③
④
TTa
POWER
START
RELAY
OUT
T
OND
ON Delay
1. Timing operation starts when START signal is ON at status of power on.
2. Output will be ON when timing operation is progressed up to the setting time. Display value will be
HOLD. (
①
position)
3. When RESET signal is ON, display value and output will be reset.(
②
position)
4. If RESET signal is OFF while START signal is ON,“STEP 1”will be restarted.(
③
position)
5. When START signal is OFF, display value and output will be reset.(
④
position)
[
ONd1
]
POWER
START
RESET
RELAY OUT
Set time
Set time
0
0
UP
DOWN
T T
①
②
③
TTa
POWER
START
RESET
RELAY
OUT
T
OND
Ⅰ
ON Delay 1
1. Timing operation starts when START signal is ON at status of power on.
2. Output will be ON when timing operation is progressed up to the setting time. Display value will be
HOLD.(
①
position)
3. Even though START signal is applied repeatedly, only the initial signal is recognized.(
②
position)
4. When RESET signal is ON, display value and output will be reset.(
③
position)
[
ONd2
]
POWER
START
RESET
RELAY OUT
Set time
Set time
0
0
UP
DOWN
T T
①
②
TTa Ta
T
Tout
POWER
START
RELAY
OUT
OND
Ⅱ
ON Delay 2
(One-shot output)
1. Timing operation starts when START signal is ON at status of power on.
2. Time limit output will be ON and goes OFF during Tout setting time when timing operation is progressed
up to the setting time. Display value will be HOLD.(
①
position)
3. When RESET signal is ON, display value and output will be reset.
4. If START signal is applied while time is progressing, Timing operation will be reset and started again. (
②
position)
5. Tout setting range: 0.01 sec to 99.99 sec.
[
FLK
]
POWER
START
RESET
RELAY OUT
Toff
Toff
Ton
Ton
0
0
UP
DOWN
Toff Toff Toff Toff ToffTon Ton
Ton
Ta Ta Ta
Toff Ton Toff Ton
POWER
START
RELAY
OUT
FK
Flicker
(Toff operation
precedes)
1. If START signal is ON, output will be repeatedly OFF during Toff setting time and will be OFF during Ton
setting time when power is ON.
2. When RESET signal is ON, display value and output will be reset.
3. If RESET signal is OFF when START signal is ON, “STEP 1” will be restarted.
4. When START signal is OFF, display value and output will be reset.
5. It is able to set each Toff time and Ton time separately. In [
] mode, timing operation starts with Toff.
[
FLk1
]
POWER
START
RESET
RELAY OUT
Toff
Toff
Ton
Ton
0
0
UP
DOWN
①
Toff
Toff
ToffTon Ton Ton Ton
Ton
Ta Ta Ta
POWER
START
RELAY
OUT
Ton Toff Ton
FK.
Ⅰ
Flicker 1
(Ton operation
precedes)
1. IF START signal is ON, output will be repeatedly ON during Ton setting time and will be OFF during Toff
setting time when power is ON.
2. Even though START signal is applied repeatedly, only the initial signal is recognized.(
①
position)
3. When START signal is ON, display value and output will be reset. If START signal is ON, it will be
restarted.
4. It is able to set each Toff time and Ton time separately. In [
] mode, timing operation starts with Ton.
T > Ta
Ton, Toff > Ta
T > Ta
T > Ta
Ton, Toff > Ta
T = set time
T = set time
Tout = output time
T = set time
Ton, Toff = set time
Enables to set Ton and
Toff time differently.
Ton, Toff = set time
Enables to set Ton and
Toff time differently.