Avantgarde UNO SD - Subwoofer DSP Amplifier Controls

24 25
SAFETYINSTALLATIONOPERATION SUBFINE TUNING
MISC
WARRANTY
OPERATION
SAFETYINSTALLATIONOPERATION SUBFINE TUNING
MISC
WARRANTY
OPERATION
OPERATION – SUBWOOFER DSP AMP
POWER SWITCH, INPUT SELECT SWITCH & LED BRIGHTNESS
POWER SWITCH
The mains power switch has an “O” OFF–position & an “1” ON–
position. For operation switch to the ON position. If the SPACEHORN
is not being used for a longer time, switch the system to the “0”
OFF–position.
INPUT SELECT SWITCH
Speaker Level & balanced inputs can be connected in parallel. With
the Input–Select switch the respective input can be selected.
The Input–Select switch also has a MUTE–position, which mutes
the inputs. This can be helpful during troubleshooting (e.g. when
hum occurs).
LED BRIGHTNESS CONTROL
The brightness of the LED light can be adjusted with the DIMMER
TOGGLE button , toggling through 8 x intensities.
OPERATION – SUBWOOFER DSP AMP
POWER MODE SETTINGS
POWER MODE SWITCH
4 x different power ON/OFF modes can be selected with the POWER
ON mode selector . Use a screwdriver to switch the modes.
newly selected modes will only become active after the
mains power switch has been switched OFF & ON again!
MODE A speaker is ON upon powering it up with the mains
power switch . To be used e.g. for remote controlled
AC power sockets.
MODE B speaker is ON when a 12VDC trigger voltage is
detected at the remote-trigger socket . The speaker
will automatically switch OFF, when the 12V trigger
voltage is switched OFF.
MODE C the illuminated push button on the front of the
loudspeaker (see page 19), is used to toggle between
ON & STANDBY.
MODE D speaker is switched ON & STANDBY by remote control
signal (optional future upgrade only).
OPERATION SUB OPERATION SUB
+ 1.5
+ 3
+ 6
WARNING
ELECTRICAL SHOCK HAZARD
DO NOT OPEN!
110 – 240V ~ 50/60HZ
MAX POWER CONSUMPTION – 570W
POWER OUTPUT – 530W RMS
FUSE 2.5 A SLOW
0dB 0dB
– 1.5
– 3
– 6
TOTAL GAINDRIVER GAIN
MIDRESET HIGH IN
OUT
BALANCED INPUT
+ 1.5
– 1.5
+ 1.5
– 1.5
0dB
ENGAGED
FUSE
E FUSE
UNO G3 DUO G3
ITRON AMP
MADE IN GERMANY
SPEAKER TYPE
MODEL NO.
ORIGIN
SERIAL NO.
only to be used with marked speaker type
WARNING
ELECTRICAL SHOCK HAZARD
DO NOT OPEN!
110 – 240V ~ 50/60HZ
MAX POWER CONSUMPTION – 550W
POWER OUTPUT – 500W RMS
FUSE 4.0 A SLOW
CLIP
VOL
VOL
SIG
SERVICE USE ONLY
SPEAKER LEVEL INPUT
GROUND
DSP
DSP PROGRAMMING
SERIAL NO.
BASSAMP-G3-500
MADE IN GERMANY
MODEL NO.
ORIGIN
SPEAKER TYPE
UNO SD DUO SD
only to be used with marked speaker type
SERVICE USE ONLY
FUSE
PUSH
PUSH
5
WARNING
ELECTRICAL SHOCK HAZARD
DO NOT OPEN!
110 – 240V ~ 50/60HZ
MAX POWER CONSUMPTION – 550W
POWER OUTPUT – 500W RMS
FUSE 4.0 A SLOW
CLIP
VOL
VOL
SIG
SERVICE USE ONLY
12V DC
ENGAGED
FUSE
OUT IN
INPUT
SPEAKER LEVEL INPUT
OUTPUT
BALANCED SIGNAL
SPKR
RESET
MODE
XLR
MUTE
INPUT SELECTE FUSE
GROUND
POWER
TOGGLE
DIMMER
TRIGGER
DSP
DSP PROGRAMMING
A D
B C
SERIAL NO.
BASSAMP-G3-500
MADE IN GERMANY
MODEL NO.
ORIGIN
SPEAKER TYPE
UNO SD DUO SD
only to be used with marked speaker type
SERVICE USE ONLY
FUSE
PUSH
WARNING
ELECTRICAL SHOCK HAZARD
DO NOT OPEN!
110 – 240V ~ 50/60HZ
MAX POWER CONSUMPTION – 550W
POWER OUTPUT – 500W RMS
FUSE 4.0 A SLOW
SERVICE USE ONLY
SPEAKER LEVEL INPUT
OUTPUT
BALANCED SIGNAL
SPKR
XLR
MUTE
INPUT SELECT
SERIAL NO.
WARNING
ELECTRICAL SHOCK HAZARD
DO NOT OPEN!
110 – 240V ~ 50/60HZ
MAX POWER CONSUMPTION – 550W
POWER OUTPUT – 500W RMS
FUSE 4.0 A SLOW
CLIP
VOL
VOL
SIG
SERVICE USE ONLY
12V DC
ENGAGED
FUSE
OUT IN
INPUT
SPEAKER LEVEL INPUT
OUTPUT
BALANCED SIGNAL
SPKR
RESET
MODE
XLR
MUTE
INPUT SELECTE FUSE
GROUND
POWER
TOGGLE
DIMMER
TRIGGER
DSP
DSP PROGRAMMING
A D
B C
SERIAL NO.
BASSAMP-G3-500
MADE IN GERMANY
MODEL NO.
ORIGIN
SPEAKER TYPE
UNO SD DUO SD
only to be used with marked speaker type
SERVICE USE ONLY
FUSE
PUSH
WARNING
ELECTRICAL SHOCK HAZARD
DO NOT OPEN!
110 – 240V ~ 50/60HZ
MAX POWER CONSUMPTION – 550W
POWER OUTPUT – 500W RMS
FUSE 4.0 A SLOW
SERVICE USE ONLY
ENGAGED
FUSE
INPUT
SPEAKER LEVEL INPUT
OUTPUT
BALANCED SIGNAL
SPKR
RESET
XLR
MUTE
INPUT SELECTE FUSE
TOGGLE
DIMMER
DSP
DSP PROGRAMMING
SERIAL NO.
BASSAMP-G3-500
MADE IN GERMANY
MODEL NO.
ORIGIN
SPEAKER TYPE
UNO SD DUO SD
only to be used with marked speaker type
PUSH
1 6
1 7
WARNING
ELECTRICAL SHOCK HAZARD
DO NOT OPEN!
110 – 240V ~ 50/60HZ
MAX POWER CONSUMPTION – 550W
POWER OUTPUT – 500W RMS
FUSE 4.0 A SLOW
CLIP
VOL
VOL
SIG
SERVICE USE ONLY
12V DC
ENGAGED
FUSE
OUT IN
INPUT
SPEAKER LEVEL INPUT
OUTPUT
BALANCED SIGNAL
SPKR
RESET
MODE
XLR
MUTE
INPUT SELECTE FUSE
GROUND
POWER
TOGGLE
DIMMER
TRIGGER
DSP
DSP PROGRAMMING
A D
B C
SERIAL NO.
BASSAMP-G3-500
MADE IN GERMANY
MODEL NO.
ORIGIN
SPEAKER TYPE
UNO SD DUO SD
only to be used with marked speaker type
SERVICE USE ONLY
FUSE
PUSH
1 8
1 9
�