Barco MVGD 1318 CR/ER User Manual (English)

Questions and Answers:

I
igainesAug 14, 2025
What to do if the Barco MVGD 1318 CR/ER Monitor screen remains black?
- P
  Paul RussellAug 14, 2025
  If your Barco Monitor screen remains black, there are several things you can check. First, ensure you have followed the correct installation procedure. If the LED at the front of the monitor is orange, the display is in stand-by mode. Verify in the Windows Display Properties that the display controller video heads are attached; otherwise, there will be no image. Also, the external power supply might be defective.
J
Justin LoveAug 17, 2025
How to fix image noise or interference on Barco Monitor?
- B
  Brandon DuncanAug 17, 2025
  If your Barco Monitor image exhibits noise or interference, consider these solutions: The video cable may be of poor quality, so try replacing it. Ensure the DVI video cable is firmly connected to both the PC and the display. If you are using analog video, the display may need Phase and Frequency adjustments.
M
Mitchell RayAug 21, 2025
How to correct a non-proportionally spread image on Barco MVGD 1318 CR/ER?
- T
  Tina MorrisAug 21, 2025
  To correct a non-proportionally spread image on your Barco Monitor, try the following: Select another resolution in the Windows “Display Properties” control panel. Alternatively, switch the “Scaling” function in the display's OSD (Geometry menu) to “None” or “Best Fit.”
J
Jessica SuttonAug 25, 2025
What to do if PC does not start up with Barco MVGD 1318 CR/ER?
- L
  lisamoralesAug 25, 2025
  If your PC does not start up when connected to the Barco Monitor, you can try the following: Check the CMOS settings in the PC BIOS. Also, ensure that the display controller is firmly seated in the PCI connector.
D
Daniel ClarkAug 27, 2025
How to fix a 90 degree rotated image on Barco Monitor?
- M
  mary74Aug 27, 2025
  To fix an image that is rotated 90° on your Barco Monitor, select another resolution in the Windows “Display Properties” control panel.
M
michaelosbornAug 30, 2025
What to do if nothing happens when pressing or rotating the control wheel on Barco Monitor?
- M
  Maria PenningtonAug 30, 2025
  If nothing happens when you press or rotate the control wheel on your Barco Monitor, the User Controls may be disabled. Please read the paragraph about the “User Controls” function.
W
William VargasSep 3, 2025
Why are images switched on dual-head Barco MVGD 1318 CR/ER system?
- J
  jeremybakerSep 3, 2025
  If, on a dual-head system, the images on the left and right Barco Monitor displays seem to be switched, switch the video cables at the display controller or at the display video inputs.
S
Susan MorrisSep 6, 2025
Why does the previous image remain visible on the Barco MVGD 1318 CR/ER Monitor screen?
- Q
  qperezSep 6, 2025
  This phenomenon, called “image sticking,” is normal if the same image has been on the screen for a long time. The ghost image will disappear after some time. Over 10 hours operation with the same image content is not recommended. Switching on the display DPMS may decrease the risk of image sticking. A slight case of image sticking can be solved by continuously displaying a full white image during a number of hours.
T
Traci MccormickSep 9, 2025
Is it normal for Barco MVGD 1318 CR/ER image to contain missing pixels?
- J
  Joshua ClarkeSep 9, 2025
  A number of missing pixels may be normal, as this is inherent in LCD technology.

Barco MVGD 1318 CR/ER Specifications

General

Display technology	LCD
Native resolution	1280 x 1024
Resolution	1280 x 1024
Aspect Ratio	5:4
Storage Temperature	-20°C to 60°C
Viewing Angle	170° horizontal, 170° vertical
Input Connectors	VGA
Operating Temperature	0°C to 40°C