BEA IXIO Series User Manual

75.5961.05 IXIO FAMILY QG 20230410 Page 1 of 4
IXIO FAMILY
! !
1
Activation and safety sensors
for automatic sliding doors
ENGLISH
READ BEFORE BEGINNING INSTALLATION & SETUP
Refer to the User’s Guide
for full instructions.
This device can be expected to comply with Part 15 of the FCC Rules, provided it is assembled in
exact accordance with the instructions provided with this kit. Operation is subject to the following
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Only trained and
qualified personnel
are recommended for
installation and setup of the
sensor.
The warranty is invalid if
unauthorized repairs are
made or attempted by
unauthorized personnel.
Following installation,
always test for proper
operation (according to
ANSI 156.10) before leaving
the premises.
The door control unit
and the header cover
profile must be correctly
grounded.
max. 2 in
CAMERA HARNESS FOR DT1 V
RED
SENSOR
DOOR CONTROL
BLACK
BROWN
BLUE
WHITE (COM)
YELLOW (N.C)
GREEN (N.O.)
PURPLE
PURPLE
POWER SUPPLY
POWER SUPPLY
SAFETY INPUT
SAFETY INPUT
TEST OUTPUT*
TEST OUTPUT*
OPENING INPUT
OPENING INPUT
OPENING INPUT
The sensor should be
mounted securely to
avoid extreme vibrations.
Avoid highly reflective
objects in the infrared
field.
Avoid moving objects
and light sources in the
detection field.
Do not cover the sensor.
MOUNTING & WIRING
Sensor connectivity (power and relays) must utilize only
the supplied harness.
Sensor power must be supplied from a Class 2 supply
source limited to 15 W.
Sensor is intended to be monitored for proper
operation by the door operator or system.
Harness shall be routed separated from any Mains or
non-Class 2 voltage cable for correct operation or shall
be rated for the Mains voltage, and suitable protection
and routing means shall be used according to National
and Local Codes to prevent damage to the harness
and/or IXIO sensor.
RCA VIDEO OUT ♀
POWER
(12 – 24 VAC/VDC)
Refer to Application Note 76.0035 if an IXIO Spacer is required for the given application.
QUICK GUIDE
POWER
12 – 24 VAC/VDC
12 – 30 VDC
2.5 W (max)
TEST
low: < 1 V
high: > 10 V (30 V max.)
response time: typ. < 5 ms

BEA IXIO Series Specifications

General

IP Rating	IP54
Detection Range	Adjustable
Power Supply	12 - 24 VAC ±10%; 12 - 24 VDC +30% / -10%
Temperature Range	-20°C to +55°C
Output	Relay
Relay Hold Time	Adjustable
Housing Material	ABS
Dimensions	120 mm (H)

Summary

Installation and Setup Prerequisites

Pre-Installation Safety and Guidelines

Key warnings and recommendations for safe and correct installation and setup.

Mounting and Wiring Instructions

Radar Opening Impulse Field Configuration

Angle and Width Adjustments

Adjusting the tilt and rotation for angle, and selecting between wide or narrow detection width.

Infrared Safety Field Configuration

Safety Field Angle and Width

Adjusting the safety field angle and verifying the detection width for proper operation.

Setup Procedures

Quick and Assisted Setup

Performing quick or assisted setup using the knob or remote control.

LED Signal Indicators

Understanding LED signals for motion detection, presence, and AUX sensors.

Overview of Settings

Basic Settings Overview

Configuration options for RAD field size, immunity, direction, holdtime, and reentry.

Advanced Settings Overview

Configuration options for AIR width, number, presence time, output, and redirection.

Factory Reset and Diagnostics

Performing factory resets and accessing diagnostic information like error logs.

Notes on Settings

Setting Adjustment Guidance

Notes on using screwdrivers for AIR adjustments and understanding relay terminology.

Sensor LED and Monitoring

Information on the sensor LED behavior and external monitoring functionality.

Output and Input Definitions

Definitions for MTF, opening output activation, and presence detection inputs.

Technical Specifications

Power and Mounting Specifications

Details on supply voltage, voltage regulator, and mounting height requirements.

Output and Test/Monitoring Specs

Specifications for electromechanical and solid-state relay outputs and test inputs.

Installation and Service Compliance

Manufacturer Responsibilities and Recommendations

BEA's liability disclaimer and recommendations for certified installation and service personnel.

Safety Inspection and Labeling

Requirements for safety inspections, compliance with regulations, and proper signage.