9487 Dielman Rock Island Ind Dr, St. Louis, MO 63132 www.becs.com
Operation and Maintenance Manual
Rev:
K12
T
T
A
A
B
B
L
L
E
E
O
O
F
F
C
C
O
O
N
N
T
T
E
E
N
N
T
T
S
S
Warnings ............................................................................. 1
General Guidelines ............................................................. 2
Firmware Version ............................................................... 2
Environmental Conditions .................................................. 2
Electrical Specifications ...................................................... 2
NSF Suggested Operation Ranges ...................................... 3
Applicable Sensor Operation Ranges ................................. 3
Section A: Programming the Controller ............................ 4
A – 1: Controller Options .............................................. 4
A – 2: The Program Menu ............................................. 4
A – 2.1: Entering the Program Menu ......................... 4
A – 2.2: Selecting Language ...................................... 4
A – 2.3: pH High Alarm Point ................................... 4
A – 2.4: pH Low Alarm Point .................................... 4
A – 2.5: ORP High Alarm Point ................................ 4
A – 2.6: ORP Low Alarm Point ................................. 5
A – 2.7: Temperature High Alarm Point .................... 5
A – 2.8: Temperature Low Alarm Point .................... 5
A – 2.9: ORP/ppm Set point ...................................... 5
A – 2.10: ppm High Alarm ........................................ 5
A – 2.11: ppm Low Alarm ......................................... 5
A – 2.12: Exiting the Menu ........................................ 5
Section B: Normal Operation ............................................. 6
B – 1: Set points ............................................................. 6
B – 1.1: Displaying the Set points .............................. 6
B – 1.2: Modifying the Set points .............................. 6
B – 1.2.1: pH Set Point .......................................... 6
B – 1.2.2: Chlorine Set Point ................................. 6
B – 1.2.2.1: ORP Control ................................... 6
B – 1.2.2.2: ppm Control (Calculated) ............... 6
B – 1.2.2.3: ppm Control (Probe) ....................... 6
B – 1.2.3: Booster Trigger Point ............................ 6
B – 1.2.4: Booster End Point .................................. 6
B – 2: Single Point Calibration ...................................... 7
B – 2.1: Single Point Calibration - pH ....................... 7
B – 2.2: Single Point Calibration - Temp ................... 7
B – 2.3: Single Point Calibration – ppm .................... 7
B – 2.3.1: Calculated ppm ...................................... 7
B – 2.3.2: ppm Probe ............................................. 7
B – 2.4: Probe Error ................................................... 7
B – 3: Alarms ................................................................. 7
B – 3.1: pH High/Low alarms .................................... 7
B – 3.2: ORP High/Low alarms ................................. 7
B – 3.3: ppm High/Low alarms .................................. 7
B – 3.4: Temperature High/Low alarms .................... 7
B – 3.5: No Flow Alarm............................................. 8
B – 3.6: Flow Restored Delay .................................... 8
B – 3.7: Cl/Br Lockout ............................................... 8
B – 3.8: pH Failsafe ................................................... 8
B – 3.9: Cl/Br Failsafe ............................................... 8
B – 3.10: Booster FAILSAFE .................................... 8
B – 4: Resetting a Failsafe Alarm .................................. 8
Section C: Using the BECSysRCM3 ................................. 9
C – 1: Monitoring a Controller ....................................... 9
C – 2: Downloading Data Logs ...................................... 9
C – 2.1: Using a Flash Drive .................................... 10
C – 2.1.1: Importing Data Logs ............................ 11
C – 3: Viewing Data Logs ............................................ 11
Section D: Troubleshooting .............................................. 12
D – 1: BECSys3 ........................................................... 12
D – 1.1: Probe Error ................................................. 12
D – 2: BECSysRCM3................................................... 12
D – 2.1: Problems Using A Flash Drive ................... 12
D – 2.2: Text Message Call-Out Test ....................... 12
Section E: Maintenance .................................................... 13
E – 1: Potentiometric Sensors (pH and ORP) ............... 13
E – 1.1: Electrode Cleaning: ..................................... 13
E – 1.2: Long-Term Storage: .................................... 13
E – 2: CCS140 Free Chlorine Sensor ........................... 13
E – 2.1: Cleaning ...................................................... 13
E – 2.2: Long-Term Storage ..................................... 13
E – 2.3: Filling electrolyte ........................................ 13
Section F: Feed Charts ..................................................... 14
F – 1: Spa Feed Charts ................................................. 14
F – 2: Pool Feed Charts ................................................ 15
Section G: Installation Diagrams ...................................... 16
G – 1: Pressure Filter Installation ................................. 16
G – 2: Vacuum Filter Installation ................................. 16
Section H: Replacement Parts .......................................... 17
Section I: Warranty .......................................................... 18
To Next Page
Loading...
