BeiJer BFI-H3 - Table of Contents; 3 Contents

Beijer Electronics Frequency Inverter BFI-H3 KI00363B 2019-09
www.beijer.se www.beijer.no www.beijer.dk www.beijerelectronics.de www.beijerelectronics.com www.beijerelektronik.com.tr 2 (29
)
3 Contents
1 START-UP DOCUMENT .................................................................................................................................................. 1
2 IMPORTANT SAFETY INFORMATION ......................................................................................................................... 1
3 CONTENTS ........................................................................................................................................................................ 2
4 INSTALLATION ................................................................................................................................................................. 3
4.1 PHYSICAL DIMENSIONS IP66 ........................................................................................................................................... 3
4.2 PHYSICAL DIMENSIONS IP20 ........................................................................................................................................... 4
4.3 PHYSICAL DIMENSIONS IP55 ........................................................................................................................................... 5
4.4 FUSES, CABLE DIMENSIONS AND POWER LOSES ............................................................................................................. 6
4.5 DERATING INFORMATION ................................................................................................................................................. 7
4.6 OVERVIEW OF POWER SUPPLY, GROUNDING AND MOTOR CABLE ................................................................................... 8
4.7 SAFE TORQUE OFF, STO ................................................................................................................................................ 9
4.8 OVERVIEW CONTROL INPUTS/OUTPUTS ........................................................................................................................... 9
5 BASIC PARAMETER SETTING ................................................................................................................................... 10
5.1 DIGITAL START IN ONE DIRECTION AND ONE PRESET OR ANALOG SETPOINT ............................................................... 10
5.2 DIGITAL START IN TWO DIRECTIONS AND ONE PRESET OR ANALOG SETPOINT ............................................................ 11
5.3 DIGITAL START SIGNAL IN TWO DIRECTIONS AND 8 FIXED PRESET SPEEDS ................................................................. 12
5.4 ALARM RESET ................................................................................................................................................................. 13
5.5 TRANSISTOR OUTPUTS 24 VDC OR ANALOG OUTPUT, 0-10 V/4-20 MA ...................................................................... 13
5.6 RELAY OUTPUTS............................................................................................................................................................. 13
5.7 FIELDBUS CONTROL SETTINGS ...................................................................................................................................... 14
5.8 FIELDBUS COMMUNICATION PROTOCOL ........................................................................................................................ 14
5.9 PTC-THERMISTOR ......................................................................................................................................................... 15
5.10 CONTROL FROM A MODBUS RTU MASTER .................................................................................................................... 16
5.11 VECTOR CONTROL ......................................................................................................................................................... 17
5.12 PID-CONTROL ................................................................................................................................................................ 18
5.13 BFI-SMARTSTICK ........................................................................................................................................................... 20
6 KEYPAD ............................................................................................................................................................................ 21
6.1 DRIVE OPERATING DISPLAY – OLED KEYPAD, IP55 AND IP66 .................................................................................. 21
6.2 ACCESSING AND CHANGING PARAMETER VALUES – OLED KEYPAD .......................................................................... 22
6.3 RESETTING PARAMETERS TO FACTORY DEFAULT SETTINGS – OLED KEYPAD ......................................................... 22
6.4 CHANGING THE LANGUAGE ON THE OLED DISPLAY – OLED KEYPAD ....................................................................... 23
6.5 SELECTING BETWEEN HAND AND AUTO CONTROL – OLED KEYPAD .......................................................................... 23
6.6 KEYPAD SHORT CUTS .................................................................................................................................................... 24
6.7 MONITORING FROM KEYPAD .......................................................................................................................................... 25
7 GENERAL SPECIFICATION ......................................................................................................................................... 26
8 WARNING AND ALARM CODES ................................................................................................................................ 27
Copyright © Beijer Electronics, 2019
This software/documentation/information (below referred to as ‘the material’) is the property of Beijer Electronics. The holder
or user has a non-exclusive right to use the material.
The holder is not allowed to distribute the material to anyone outside his/her organization except in cases where the material is
part of a system that is supplied by the holder to his/her customer.
The material may only be used with products or software supplied by Beijer Electronics.
Beijer Electronics assumes no responsibility for any defects in the material, or for any consequences that might arise from the
use of the material.
It is the responsibility of the holder to ensure that any systems, for whatever applications, which is based on or includes the
material (whether in its entirety or in parts), meets the expected properties or functional requirements.
Beijer Electronics has no obligation to supply the holder with updated versions.