10
TO.GO AK / HAPPY AK / IRI.TX AK
Cloning is intended as the ability of the AK series transmitters to be programmed with the same code as an ARC or Fixed Code* tran-
smitter already saved on a receiver, or to replace most fixed-code transmitters on the market with a simple and fast procedure without
the need to access the receiver nor to open the remote control.
An important innovation featured by these new AK versions is the implementation of double-encoding, ARC or fixed: this transmit-
ter can be used as a normal cloneable transmitter or as a real ARC transmitter with variable code.
In fact, the AK radio control, if not used to clone a fixed code transmitter, sends the code by default with Advanced Rolling Code
encoding.
The only way to make it use the fixed-code is to program it starting from TO.GOWP or TO.GOWK or by other AK series transmit-
ters already programmed with fixed code.
Quick cloning
With quick cloning you get a transmitter that replicates exactly every single channel of the original transmitter (already memorized)
in the new transmitter AK; we recommend using a 2AK to clone a two-channel original transmitter and a 4AK to clone a four-chan-
nel transmitter.
Proceed as follows:
1) press and hold the key T1 of the new transmitter AK. When pressing T1, the LED lights up steadily, after 5 seconds it will begin
to flash rapidly, after 15s to flash slowly.
2) after about 15s, put the original transmitter near the new transmitter as shown in the picture, and continue to hold the key T1 on
the new remote control, and press any button on the original remote control.
3) if the procedure was completed successfully, the LED of the new transmitter AK will turn off. Release all the keys pressed.
All channels of the original transmitter are replicated on the new AK transmitter.
N.B.: Use for both remote controls batteries charged.
If after 15 sec. the red LED on the new transmitter is not off, release the buttons of the remote control and after 1 minute, repeat
from step 1, being careful to place the original transmitter as shown in the picture.
Advanced cloning
In advanced cloning you can choose which channel of the original transmitter (already memorized) will be replicated on the new
AK transmitter.
For example, you can replicate channel 3 of an old transmitter on channel 1 of a AK transmitter, which is not possible during quick cloning.
Proceed as follows:
1) on the new AK, press and hold the key of which you want to replicate the function of the original. When you press the button,
the LED lights up steadily, after 5 seconds it will begin to flash rapidly.
2) after 5s, put the original transmitter near the new transmitter as shown in the picture, and continue to hold the key on the new
remote control, and press the button of the original remote control whose code you intend to copy.
3) if the procedure was completed successfully, the LED of the new transmitter AK will turn off. Release all the keys pressed.
The channel chosen in the original transmitter is now replicated in the AK transmitter.
N.B.: Use for both remote controls batteries charged.
If after 30 sec. the red LED on the new transmitter is off, release the buttons of the remote control and repeat from step 1, being
careful to place the original transmitter as shown in the picture.
* Transmitters with HCS coding cannot be cloned.
ATTENTION!
The positions indicated in the following figures guarantee the best communication among transmitters during the cloning phase.
NEW: New AK transmitter - ORIGINAL: Transmitter already saved.
TRANSMITTER CLONING
>
IRI.TX > IRI.TX AK
IRI.TX > TO.GO AK
HAPPY > HAPPY AK
HAPPY > IRI.TX AK
TO.GO > TO.GO AK
IRI.TX.GO > TO.GO AK
NEW
ORIGINAL
NEW
ORIGINAL
NEW
ORIGINAL
NEW
ORIGINAL
NEW
ORIGINAL
NEW
ORIGINAL
To Next Page
Loading...
Need help?
General
